Models > GFS165

GFS165 (MN10) Caloric Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for GFS165

Viewing 7 of 7
Cabinet Parts Diagram and Parts List for MN10 Caloric Refrigerator
Cabinet Parts
Compartment Separator Parts Diagram and Parts List for MN10 Caloric Refrigerator
Compartment Separator Parts
Freezer Door Parts Diagram and Parts List for MN10 Caloric Refrigerator
Freezer Door Parts
Liner Parts Diagram and Parts List for MN10 Caloric Refrigerator
Liner Parts
Refrigerator Door Parts Diagram and Parts List for MN10 Caloric Refrigerator
Refrigerator Door Parts
Shelf Parts Diagram and Parts List for MN10 Caloric Refrigerator
Shelf Parts
Unit Parts Diagram and Parts List for MN10 Caloric Refrigerator
Unit Parts
Keep searches simple, eg. "belt" or "pump".
High Limit Thermostat – Part Number: 489P3
This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element.
No Longer Available
Igniter – Part Number: WP37001308
$48.21
The bracket is no longer included.
In Stock
Order now and your part arrives by May 29
Refrigerator Cold Control Thermostat – Part Number: 1123394
$108.25
This cold control thermostat has a temperature range from 29.5 degrees Fahrenheit to 16.5 degrees Fahrenheit and a capillary length of 35 inches.
In Stock
Order now and your part arrives by May 29
THERMOSTAT,LOW LIMIT – Part Number: 56591
No Longer Available
Trim, Top – Part Number: 311646
No Longer Available
SWTCH-PRCT – Part Number: 314210
No Longer Available
Nut – Part Number: 311137
Nut
No Longer Available
DISCONTINUED – Part Number: Y0056856
No Longer Available
Tube, Vent – Part Number: 310835
No Longer Available
Bracket, Front Support (2) – Part Number: 311638
No Longer Available
Retainer, Glass (sold individually, 4 recommended) – Part Number: 310823
No Longer Available
DISCONTINUED – Part Number: 56755
No Longer Available
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for GFS165

Viewing 4 of 4
Not Heating
Fixed by these parts
Fixing
How to fix it
Too hot
Fixed by these parts
Fixing
How to fix it
Fridge too warm
Fixed by these parts
Fixing
How to fix it
Fridge too cold
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
William from Placentia, CA
Parts Used:
WP37001308
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Gas dryer was not getting hot.
Removed top of dryer and front panel. Keeping the front door closed I was able to start the unit and observe if the gas was igniting to heat the unit.
Found that no flame was present.
Examined the ignitor (found the locatino after utilizine this website parts diagram) and noticed it was cracked.
Ordered the new part and it arrived two days later. Simple installation and ta daaa....ignitor works, hot dryer again.
*Only reason it took over half an hour was because I cleaned out all the internal vents while the unit was opened.
Basic mechanical abilities required here but remember to unplug the unit while working on it!
Read less
11 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RICHARD from LINDSTROM, MN
Parts Used:
WP37001308
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Would not lite
Remove igniter and replaced easy to do
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Mokena, IL
Parts Used:
489P3
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
At the end of the drying cycle, the clothes had a bunt smell. I checked the lower compartment of the dryer and found the limit thermostat in two pieces and realized this could be the culprit. I was able to snap them together, but this did not work, therefore a new stat
First I unpluged the dryer, removed the two screws from the bottom access panel. I used a small socket to remove the screws securing the limit stat to the burner chamber, nut driver was too long.
I installed the new limit stat with the two screws and attached the two leads. Plugged in the dryer and conducted a test run, burner ig nited. I turned the dryer off and replaced the access panel.
Read less
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More