Models
>
XRSS665BB
XRSS665BB (PXRSS665BB0) Amana Refrigerator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for XRSS665BB
Viewing 16 of 16
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for PXRSS665BB0 Amana Refrigerator")
Keep searches simple, eg. "belt" or "pump".
$9.79
This part helps with the closing of the door and helps keep them in position.
In Stock
Order now and your part arrives by Apr 10
$21.82
This is a screw and it is made for multiple appliances in your home. This model is called a sheet metal screw because it has sharp points, and the threads are closer together. This screw is designed t...
In Stock
Order now and your part arrives by Apr 10
$7.60
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order now and your part arrives by Apr 10
In Stock
Order now and your part arrives by Apr 10
$102.93
Sold individually.
Front Width: 16.8;
Front to Back: 14.9";
Width at Rear: 16.42.
In Stock
Order now and your part arrives by Apr 10
$28.91
If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate...
In Stock
Order now and your part arrives by Apr 10
This right side shelf support is just over an inch long. It is all white in color and it is made entirely of plastic.
No Longer Available
This wheel is sold individually. It is located on the bottom of the refrigerator.
In Stock
Order now and your part arrives by Apr 10
$11.98
This is a compression nut for your refrigerator/freezer. The compression nut is used with the plastic water line for the icemaker assembly. It is the connection between the water supply line and the o...
In Stock
Order now and your part arrives by Apr 10
This part is the replacement ice chute door for your refrigerator/freezer. It is a round, black part that is approximately 2 ½ inches in diameter. The dispenser ice chute door opens to let ice through...
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for XRSS665BB
Viewing 12 of 12Leaking
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Clicking sound
Fixed by these parts
How to fix it
Not dispensing water
Fixed by these parts
How to fix it
Door Sweating
Fixed by these parts
How to fix it
Light not working
Fixed by these parts
How to fix it
Ice maker not making ice
Fixed by these parts
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
How to fix it
Too warm
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Russ from Asheville, NC
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door would not close
After emptying the refrig. door, I unscrewed the plate on the top of the refrigerator that covered the door bolts. Then off with the three bolts. I removed the door by lifting it up a few inches. The two parts of the door cam were easily removed and replaced with the new part. BEFORE REPLACING the door spread vasoline on both cam parts.
... Read more
(Not after as I did. The second time you do any of these repairs go SO much better :o)
After putting the door back on, adjust the tension of the screws holding the door in place if needed to align the door on the cams so that it shuts completely. Failure to do this will require taking the top off the door again. (see comment above on "... second time...")
If all is properly aligned, the door should swing completely shut.
Even with the mistakes that required removing the door to lubricate the cams, and removing it AGAIN to readjust the screws on the top to properly align the door on the cams, this was a twenty minute job. My wife and I were still speaking to one another at the end of it- a sure sign of an easy repair.
(Not after as I did. The second time you do any of these repairs go SO much better :o)
After putting the door back on, adjust the tension of the screws holding the door in place if needed to align the door on the cams so that it shuts completely. Failure to do this will require taking the top off the door again. (see comment above on "... second time...")
If all is properly aligned, the door should swing completely shut.
Even with the mistakes that required removing the door to lubricate the cams, and removing it AGAIN to readjust the screws on the top to properly align the door on the cams, this was a twenty minute job. My wife and I were still speaking to one another at the end of it- a sure sign of an easy repair.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from St. Geogre Island, FL
- Parts Used:
- WP12568001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Latch was broken on the filter cover and would not hold the filter in place.
Ordered a new filter cover, received in 2 days and installed it in about 5 minutes. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from avon, OH
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door cam worn out
remove top plastic cover / phillips screw driver
remove top door bracket / 5/15" socket
lift off door
remove pieces of old cam / phillips screw driver
replace cam/ phillips screw driver
replace door
replace top bracket / 5/16" socket
check alignment
remove top door bracket / 5/15" socket
lift off door
remove pieces of old cam / phillips screw driver
replace cam/ phillips screw driver
replace door
replace top bracket / 5/16" socket
check alignment
Was this instruction helpful to you?
Thank you for voting!