This is a genuine OEM 40-Watt replacement light bulb that is compatible with various types of appliances. It has a frosted glass bulb with a standard metal socket base, making it easy to screw and uns...
If your gas range is not lighting or coming up to temperature, there may be an issue with the igniter. The igniter is used to create a spark that lights the gas, and if it is glowing but will not ligh...
This is a screw and it is made for multiple appliances in your home. This model is called a sheet metal screw because it has sharp points, and the threads are closer together. This screw is designed t...
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
This is an oven rack for your range. It is a stable surface for your cookware to sit when baking and broiling. It measures to be roughly 23 inches wide and 16 inches long. It is made of durable metal ...
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Don
July 27, 2022
I cannot get oven to stay on display keeps showing 5abbath code, will reset panel and same thing happens
For model number GW397LXUS06
Hi Don,
Thank you for your question. According to your owner's manual, to cancel the Sabbath Mode, press and hold CLOCK for 5 seconds or after 72 hours, the Sabbath Mode will end. "Sabbath" will flash for 5 seconds and the time of day will return to the display. For more information, you will need to consult your owner's manual. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
My oven has two igniters so I needed to determine which one was the problem.
Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.
Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.
I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.
Keep track of your screws and put it back together the way you found it except for the igniter that is.
Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.
Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
First turn off circuit breaker to stove. Slide the stove out about 4 inches from the counter to expose the two phillips head screws, one on the left side and one on the right side of touch panel. Take out screws. Then take out four Phillip head screws on the bottom side of panel, this will set panel loose from stove. Carefully pull up touch pad (switch membrane) from control panel; it is sticky glued in place. Disconnect ribbon cables on switch membrane from control panel by depressing cable locks while pulling firmly. Remove switch membrane. Clean area before installing new membrane. Reassemble turn on power and you are done.
