RF354BXDW1 Whirlpool Range - Instructions

I got the model number and ordered a replacement element from partselect, was shipped quickly and I installed it in about 30 minutes, it now works great

Removed the oven racks....

Removed the two screws holding element in place...

Disconnected spade lug connectors from old heating element.

Connected spade lug connectors to new heating element.

Reinstalled screws.....replaced oven racks....mission acomplished!

First I cut off the power to the stove and double-checked to make sure no current was flowing to the unit. There were two screws attaching the bake element plate to the oven. I unscrewed the two screws and carefully pulled the bake element away from the oven exposing the contact wires. I carefully loosened the wire contacts from the bake element, slid the bake element off the contacts and then slid the new bake element onto the wire contacts. I gently clamped the contacts onto the bake element, pushed the wires back into the back of the oven and screwed back the bake element plate onto the interior of the oven. I turned on the power to test my work and I was done.

I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.

First, I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires This was challenging; the element uses blade connectors that are difficult to grab, and I didn't want to damage the connectors with pliers. Strenuous wiggling eventually worked. After that, I just reconnected the blade connectors to the new element, pushed the wires back in, and tightened the two screws.

It was fortunate that I saw a red spot on the element. When I removed it, I noticed a hole had been eaten part way through the old element. I was probably weeks away from a fire.

Start by turning off the power to the range.
It was fairly easy to take the "Control Deck" off the top of the range by removing about 8 screws. I leaned the deck forward without removing any wires except a green ground that was held on by one of the screws.
There are two small screws under the switch knob holding the Infinite Switch to the panel. I removed these and let the switch hang on the wires. To avoid missplacing or crossing the wires... I moved one wire at a time to the new switch, then attached the switch to the panel and put it all back together.
Whole job was done in about 15 minutes

Replacement was relatively easy. Oven door was pulled off hinges after removing 2 mounting screws nearest the hinges. After shutting off power at the breaker, screws (2 each) holding elements were removed. Elements were pulled into oven ~ 4 inches exposing wiring and clips. The clips pulled free with just a little wiggling by hand and were easily pushed back on by hand. Then reverse to finish.

Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette!

1. Disconnected power from my oven.
2. Removed several screws that held the control block
3. Removed two screws that held the switch itself disconnected wires and removed switch
4. Reconnected all wires to new switch (no soldiering gun required)
5. Put control block back

Overall - very easy

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

After shutting off the power, I removed the door and oven racks. Then, by using a screwdriver, I removed each element one at a time and replaced with the new element. Each element pulled away from the back wall and was connected electrically by Sta-Kon connectors. All went well, and the unit was operational in about 30 minutes. I still have to remove the oven from the wall to replaced the two door springs.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

Purchased 2 piece broiler pan from this site

Removed the two Philips head screws that attach the element to the back wall of the oven. Pulled off the two wire terminals from the spades on the back of the element. Pushed the two wire terminals onto the spades on the back of the new element. Noticed that one was not tight, so disconnected, squeezed down the wire terminal, and reconnected. Inserted the two screws that attach the element to the back wall of the oven. Element works fine.

I simply put the control knobs on the shaft and
they worked great. I love them. Thank you.