SF367PEYN1 Whirlpool Range - Instructions

took oven base plate out. diconnected ignitor , put new clips on neutral wire as per instructions, inserted new ignitor, put everything back, worked ok.

Remove broiler pan, disconnect wires from igniter to gas safety valve and connection in back corner of stove, under a metal plate held in with one screw. Remove two screws holding igniter in and take it out. With new igniter, cut neutral wire as per instructions with it, attach electrical clips to the wire ends, install the new igniter with the two screws, plug in the two wire clips to the safety valve just below the igniter and plug in the plastic clip with both wires going into it over in the corner of the stove, and replace the cover over that connection with the one screw, which you removed at the beginning of this process, and you're done.

Remove diffusers in bottom of oven,remove two screws that hold ignitor in place.Pull oven out, to access back of oven,remove three screws holding vented panel in place.Remove panel,find wires coming from ignitor,pull connectors apart and remove old ignitor.Install new ignitor in reverse order.Too bad for my wife it works fine now,she had a new oven/range picked out!

I didn't. Don't know how to get to light bulb to change it for this specific model

This was a simple replacement of the drip pans. Take the old ones out and place the new ones in. The burner tops and pan holders had to be removed first. The drip pans come out next. Then the new ones place back in. The fit was perfect. The burner tops and pan holder are replaced and your done. The range looks brand new.

Thanks.

put knob on.. fit perfectly turned the oven on.. put some cookies in to bake
Easy as pie or should I say cookie?!

Great/outstanding customer service nice people great website too! so very EASY

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!

Gently took the old one off and pushed the new one on the stem

Took the old knob off, and put the new one on.
No problem at all.

Very satisfied with the quick delivery of the part !

I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294

So super easy. I bought my oven used eight years ago when I moved into my house. I'm guessing today it is around twenty years old. It still works great but the numbers on the oven thermostat knob had worn and I could no longer read them. I went online to see if by chance I could find a replacement. Knowing my oven is so old, I was not sure what to expect. From finding the part to the fast shipping time, PartSelect impressed me 100%. I will use this web site again!!!

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Pulled knob off, pushed knob on

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.