CREW3874RB0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- RON from KAUFMAN, TX
- Parts Used:
- WP3148953
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The burner would keep heating after turning off the switch
Start by turning off the power to the range.
It was fairly easy to take the "Control Deck" off the top of the range by removing about 8 screws. I leaned the deck forward without removing any wires except a green ground that was held on by one of the screws.
There are two small screws under the switch knob holding the Infinite Switch to the panel. I removed these and let the switch hang on the wires. To avoid missplacing or crossing the wires... I moved one wire at a time to the new switch, then attached the switch to the panel and put it all back together.
Whole job was done in about 15 minutes
It was fairly easy to take the "Control Deck" off the top of the range by removing about 8 screws. I leaned the deck forward without removing any wires except a green ground that was held on by one of the screws.
There are two small screws under the switch knob holding the Infinite Switch to the panel. I removed these and let the switch hang on the wires. To avoid missplacing or crossing the wires... I moved one wire at a time to the new switch, then attached the switch to the panel and put it all back together.
Whole job was done in about 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Rockwall, TX
- Parts Used:
- W11171119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface Element Out
Took 2 screws under front edge of smooth top. Unscrewed ground wire from back of smooth top unit. Unplugged 2 wire bundles, from back. Took bad element out , put in new one. Put back together. About 10 min's tops. Easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Thornton, CO
- Parts Used:
- WPW10107820
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
E1 F5 Error on display
After reading many forums found that this error happens when trying to clean the oven and there is a failure in the latch motor to lock the oven door. It was suggested 1st to just tunr the breaker off to the over wait and then turn it back on to see if the error would clear by itself. If not then you'll have to do what I did and buy a new Latch Motor and replace it. Fairly easy to do:
) Move oven to get to the back panel
) Disconnect oven from power
) Remove the 8 screws to get the back panel off
) REmove the Latch motor screws (2) and remove the motor after twisting to get the latch rod off
) Put in new latch motor by 1st putting the latch rod in the motor assembly
) Screw the new motor in place
) Replace back panel
) Power on Oven
DONE!
) Move oven to get to the back panel
) Disconnect oven from power
) Remove the 8 screws to get the back panel off
) REmove the Latch motor screws (2) and remove the motor after twisting to get the latch rod off
) Put in new latch motor by 1st putting the latch rod in the motor assembly
) Screw the new motor in place
) Replace back panel
) Power on Oven
DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Pasadena, MD
- Parts Used:
- WP3149404
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The old switch broke off.
Removed two screws that held the unit in then pulled out a few inches so I could see where the 5 wires were. Then I replaced one at a time till done. then replaced the retaining screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramona from Mexico, MO
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The broiler element started sparking and melting in one spot. I thought it would catch on fire and quickly turned off the oven.
First we unplugged the range. My husband removed the old element using a screw driver. He also removed the back panel on the oven after pulling it out from the wall. He unplugged the broiler prongs and plugged in the new element, put it all back together using the screw driver. We plugged it back in, turned on the oven and it is working great! Simple and easy to do in a short amount of time. Cool!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hellertown, PA
- Parts Used:
- WP3149404
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner was not heating up
Puled out the electical plug . Removed the back panel. Pulled off the switch knob. Removed the 2 screws holding the switch. Took the wires off of the old switch and placed them on the corespondig connector on the new switch. Put everything back in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fruitland Park, FL
- Parts Used:
- W11171119
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Glass top stove element stopped working
really easy! Removed 2 screws under the glass top at the front, access from the open oven door, then removed the ground wire, removed the stove top, took the element holder off,( 2 screws)and replaced with new element, 30 minutes. I ordered the part and came within 18 hrs of ordering it, fantastic experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Brush, CO
- Parts Used:
- W10856603
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Oven doesn't heat evenly
Moved the stove out from the wall. Took out the screws from the back and then from the top. I pulled the piece through the back to unplug the clips from the elements. But the wires went back through the openings. So I had to take the back off of the stove to get to the wires to put back through the holes in the stove. Once the clips were back together, I put the back back on the stove. Rebolted the part to the stove and moved it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlton from lakeland, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broil element burned out
Very easy . Just removed four screws and removed the back cover. Then just unplugged two clips from the element . The repeated all of my steps in reverse . Be sure to unplug the oven before you start on the project .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Sherman, IL
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven door would not lock for self clean
switched out latch asy,rear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from POUND, WI
- Parts Used:
- WPW10434452
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Switch worked off and on but you could not set heat to a specified temperature.
Remove back panel 10 screws. Disconnect plug in fixture from switch. Front of range remove knob (it just pulls out) remove 2 screws, remove switch. To install reverse procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Farmington, NY
- Parts Used:
- W11171119
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad Element
Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturday and was cooking with it on tuesday. Great job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from SEDRO WOOLLEY, WA
- Parts Used:
- W10856603
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element failed
Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element
Was this instruction helpful to you?
Thank you for voting!