KFGD500EBS11 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MAGALIA, CA
- Parts Used:
- W10919249
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
burned the rubber feet off of the burner grates
cleaned the hole and inserted glue, then the rubber feet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from NANTUCKET, MA
- Parts Used:
- W11030413
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Chrome on knob had developed sharp edges (cut finger)
Pulled the old knob off, pushed the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Oneida, NY
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken levelling leg
Took the old levelling leg out and screw the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Hudsonville, MI
- Parts Used:
- WPW10406878
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Head burner had something spilled on it which stained it and left a large dark brown spot
Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SUN LAKES, AZ
- Parts Used:
- W11030413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Part (knob) made of cast metal, but plastic sleeve inside had broken.
Used needle nose pliers to remove flat spring steel piece which holds
knob onto spindle. Pushed replacement knob onto spindle - perfect fit.
knob onto spindle. Pushed replacement knob onto spindle - perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Highland Park, IL
- Parts Used:
- W10919249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Feet fell off early
Used Silicone Rubber to "glue" them. It's heat resistant unlike super glue which is why 8 of them fell off. I only found 6 of them and had to order replacements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from PITTSBORO, NC
- Parts Used:
- WPW10324738
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broiler burner fails to ignite
Unplug range
Shut off gas supply
Remove rear panel screws and panel with nut driver
Disconnect power plug from broiler element igniter
Open upper oven door
Remove screw from the front of the gas burner.
Remove screw using nut driver from rear of gas burner
Remove gas burner from oven and pull cord through from rear panel
Using nut driver, remove igniter from mount on gas burner
Install new igniter on mount on gas burner using nut driver
Reinstall is reverse of disassembly
Connect power and turn gas back on. Test igniter by activating broil on upper oven
Shut off gas supply
Remove rear panel screws and panel with nut driver
Disconnect power plug from broiler element igniter
Open upper oven door
Remove screw from the front of the gas burner.
Remove screw using nut driver from rear of gas burner
Remove gas burner from oven and pull cord through from rear panel
Using nut driver, remove igniter from mount on gas burner
Install new igniter on mount on gas burner using nut driver
Reinstall is reverse of disassembly
Connect power and turn gas back on. Test igniter by activating broil on upper oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BROWNVILLE, NY
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandeep from EDINA, MN
- Parts Used:
- W10777162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screw came off
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!