This holder secures components or tubing in place to maintain proper alignment. Designed for durability, it supports stable operation and system organization.
This potentiometer, also known as a spark ignition switch, sits behind a range or cooktop control knob and translates the rotation of the knob into electrical signals that regulate burner heat and ens...
This fixing kit provides the parts needed to install or replace your oven’s control board, which regulates heat and cooking functions. Compatible with select models, it’s a practical solution for rest...
This oven temperature sensor is designed to accurately measure the internal temperature of the oven cavity and relay that information to the appliance’s electronic control system for precise heat regu...
This surface burner cap is for ranges. Surface burner cap fits on top of the burner head. The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Leshawn
March 25, 2022
Double oven range. Small right oven heats but the left oven takes too long or barely heats up. The heating element in the left is warm to touch
For model number PRD484EEHU
Hello Leshawn, thank you for your question. There are a few parts that could cause this issue in your appliance. First, we would say test your elements with a multi meter to see if they are working correctly. They should be reading between 0 - 50 ohms to be working correctly. Part number (Bake) FIX8695616 (Broil) FIX8723522. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. Part number FIX8729210. If those three parts are fine however, then the issue may be in your control board. Part number FIX8733698. We hope that helps. Good luck with your repair.
The sole review for this part by Andrew was most helpful and accurate with one exception: he said that there were two nuts Which needed to be removed in order to pull off the front knob panel. There were actually two on each end for a total of four, which confused me, as I wondered if I had the right ones. Another thing that would be help
... Read moreful for somebody considering doing this repair is to know that it takes a deep quarter inch socket With two 6 inch extensions to reach these nuts through holes in the interior side panels. Also, take a look at the replacement potentiometers, and you’ll see that there’s a slot that can be lined up so that they can be pulled off the side of the shaft rather than off the front of the shaft. This repair took me about six hours. I’m mechanically inclined and work methodically, but since I’ve never done this repair before it was quite time-consuming.
Remove slide racks from oven. At the back right corner of oven unscrew heat sensor probe. Access rear of range. Remove screws holding back panel. Find wire from temperature probe where it passes through back wall of over and unclip it pulling probe wire and probe out back of oven. From the inside of oven, push chopstick through hole probe
... Read more wire was routed through, to find hole in back wall of oven. Once chopstick is visible from back of oven, with chopstick enlarge hole through visible insulation. This is the opening the new probe wire needs to be routed through. From inside oven push new wire, using chopstick, through this hole and reattach wire at back of oven using the plastic clip on the wire. From inside oven screw probe to back of oven wall, reattach outside panel to back of oven, turn gas back on, plug range back in, check oven operates, and push range back in place, reinstall racks. You may have to remove oven door if you have trouble reaching to the back of the oven to access the probe. YouTube videos are easy to find showing how to do that.
