Models > 30-2632-23

30-2632-23 ((01)) Tappan Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Drip Pan – Part Number: 5303131115
$8.92
This round chrome drip pan contains a center hole of approximately four inches wide.
In Stock
Burner Grate – Part Number: 316055800
$37.34
Sold individually.
In Stock
Clock Knob – Part Number: 318036310
Sold Individually.
No Longer Available
Flat Style Oven Igniter - Broiler – Part Number: 5303935068
$197.35
This flat style gas oven igniter comes with a bracket and wires. Its amperage range is between 3.2 and 3.6 amps.
In Stock
Flat Style Oven Igniter – Part Number: 5303935067
$62.16
This flat style gas oven igniter is 5.53 inches long and comes with a bracket and wire nuts. Its amperage range is between 3.2 and 3.6 amps. May be different in appearance but will function as the orginal part.
In Stock
KNOB – Part Number: 358T142P102
No Longer Available
SWITCH – Part Number: 316035201
No Longer Available
VALVE – Part Number: 5303288190
$114.50
Special Order
DISCONTINUED – Part Number: 5303208047
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for 30-2632-23

Viewing 1 of 1
Gas igniter glows, but will not light
Fixed by these parts
Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mariano from Torrance, CA
Parts Used:
5303131115, 316055800
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Very old burner grates & drip pans, need replacement.
Took out the old & easily replace it with the new set. No tools required.
14 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from Silver Spring, MD
Parts Used:
5303935068
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Broiler igniter not glowing
1) Turn off the gas and disconnect the power

2) Remove oven door. There requires that you remove the two square drive (SD) bolts on the inside, partially close the door and lift it off the hinges.

3) Remove the grills.

4) At the back remove the rear shield (aluminum panel held by 2 SD sheet metal screws .

5) this exposes the broiler igniter and its two wires. If its been replaced in past, there should be two porcelain screw-on wire connectors. Undo the connectors by turning them counter-clockwise. With a volt-ohmmeter, measure the resistance across the igniter. If its open circuited, its broken. If not, then its in the circuit board, and this help stop here. If this is the original igniter, it ends in a plastic connector. Disconnect by pulling it apart from its mating plug and again, check the continuity of the igniter. If its defective, reconnect the connector and cut each wire on the igniter side. Strip back about 1/2 inch of insulation on each lead.

6) inside the oven, using the SD driver, remove the 4 screw securing the broiler burner from the roof of the oven. The burner can now be removed, pulling the burner away from the gas jet on the right.

7) The igniter is now exposed and can be remove by removing the two SD drive screws.

8) Replace with the new igniter, being careful not to touch the black element, and feeding the wires though the rear oven wall.

9)Reverse the above dissembly procedure.

10) Broil the sausages.
Read less
11 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sandra from Okeene, OK
Parts Used:
5303131115
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
original drip pans were rusting on the undersides
Just to point out the pans were delivered within a few days which was very quick. I just dropped them in. They fit perfect. Thank You for no stress.
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More