37-0117-00-02 Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from Spring Valley, AL
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
Old pans/bowls were corroded
Very easy---simply unplug the burners, remove the old pans and replace with the new ones
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from New Port Richey, FL
- Parts Used:
- 5303935086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
High heat reluctant to turn down.
Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Attica, MI
- Parts Used:
- 5303935086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Right front burner would over-heat
First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.
When the switch arrived I went thru the above replacing the bad switch.
Was this instruction helpful to you?
Thank you for voting!
Old discolored drip pans that would not clean up.
I simply removed the old drip pans and inserted the new ones which matched and fit perfectly.
I'm glad I found you on line. Your service was fast and the whole transaction was easy!! Thanks.
I'm glad I found you on line. Your service was fast and the whole transaction was easy!! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Mulvane, KS
- Parts Used:
- 5303935086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The left front burner would not turn off, and the switch was sparking
First I unplugged the stove, and removed the upper-back panel. Then I pulled off the control knob. Then I removed the two screws holding the switch to the stove. Then one-by-one I removed the wires from the old switch and connected them to the corresponding tabs on the new switch. Then, using the knob adapter supplied with the new switch, I figured out how much of the knob shaft I had to remove from the new switch to position the knob the correct distance from the face of the stove. Then I tested the switch with a voltmeter as instructed, and then I hooked up the last wire.
Partselect.com is an awsome website!!! I was able to review comments form other do-it-yourselfers that had similar problems. Then I looked up the Partselect schematic drawings of my stove and was easily able to find and order the part I needed. The part arrived at my house within a couple of days and I had the stove fixed in no time.
Partselect.com is an awsome website!!! I was able to review comments form other do-it-yourselfers that had similar problems. Then I looked up the Partselect schematic drawings of my stove and was easily able to find and order the part I needed. The part arrived at my house within a couple of days and I had the stove fixed in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Lovelady, TX
- Parts Used:
- 316442300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner wouldn't stay hot.
I pulled out the old element and the new one just plugged right in.
Was this instruction helpful to you?
Thank you for voting!
Replacement bowels didn’t fit
Pulled the heating elements out took the bowels out that didn’t fit, threw them away and replaced them with the perfectly fitting bowels from this site and replaced the heating elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darren from San Diego, CA
- Parts Used:
- 5303935086
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Old switch killed by a short between wires
Turn off the electricity
Remove knob
Unscrew old switch
Lift stovetop & prop
Remove wires from switch
Remove switch
Plug wires onto new switch
Put new switch in place
Shut stovetop
Screw new switch in place
Trim knob post
Put adapter on post
Put knob back on
Turn electricity back on
Cook dinner :)
Remove knob
Unscrew old switch
Lift stovetop & prop
Remove wires from switch
Remove switch
Plug wires onto new switch
Put new switch in place
Shut stovetop
Screw new switch in place
Trim knob post
Put adapter on post
Put knob back on
Turn electricity back on
Cook dinner :)
Was this instruction helpful to you?
Thank you for voting!
Springs pooped off door hinges, causing hinges to break through door face
Remove decorative side panels on stove to expose backside of hinge and springs;
remove door;
remove old hardware;
since hinge openings were bent, straighten hinge opening in oven face;
attach spring to inside of oven;
slide hinge through opening;
attach spring to hinge;
screw hinges to oven face;
repeat on other side;
attach hinges to door;
while decorative panels are off, vacuum
install decorative panels.
DONE.
remove door;
remove old hardware;
since hinge openings were bent, straighten hinge opening in oven face;
attach spring to inside of oven;
slide hinge through opening;
attach spring to hinge;
screw hinges to oven face;
repeat on other side;
attach hinges to door;
while decorative panels are off, vacuum
install decorative panels.
DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Westfield, MA
- Parts Used:
- 316442300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement burner
Just a replacement burner for my stove. No tools needed. Thank you for such a speedy delivery
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chhabildas from Charlotte, NC
- Parts Used:
- 318372210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Enement was blew out.
I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
Surface element didn't work
Make sure whichever surface element you are to replace is OFF.Carefully remove surface element by pulling it out of socket and remove drip bowl. Cleaned area around range top and place new or old drip bowl in place. Line up drip bowl cutouts and place on range top and simply push in/plug (2 prongs)in new surface element and place on drip bowl. It's that easy! To install 2 new surface elements and drip bowls took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
Needed new drip bowls.
Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.
I was extremely pleased with the very quick delivery of needed parts.
I was extremely pleased with the very quick delivery of needed parts.
Was this instruction helpful to you?
Thank you for voting!