TGO356BHD2 Tappan Range - Instructions

The old glides were broken off so I didn't know I needed these glides until I saw the parts section of the Manuel. When they arrived I snapped them in with no effort at all.
P.S. The shipping is fantastic here......i ordered on Monday received them on Tuesday. Now that's shipping:>)

The two back door glides were missing and broken (one of each), and needed to be replaced. Finding the parts online was MUCH easier than I expected,and the repair was remarkably simple. Parts snapped into place, the drawer had to be lined up, and it slid right into place. Very easy!

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

All the was needed was a Phillips screw driver. It's not difficult. Watch out because the door is spring loaded and does seperate quickly after all the screws are out. Be sure to watch the front panel, it appears to be heavy glass and can come out of the slots during the repair. I only had to re-assemble and dis-assemble 4 times before I got it right but it's still fairly easy to do if you take your time.

Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.

i had to remove all the broken glass then removed the metal that was holding the glass. set the new glass in the metal strips and screwed it back togethr. i also had to remove the frame from the door in order to get to the inside glass. then i had to put the door back together.

The repair was fairly easy. The oven door was attached to a spring arm that had one screw holding each arm to the door. Once off, the outside set of screws were removed and saved in a small dish. Each section had 6-10 screws, to it's best to keep each set separate from each other. Each of the three layers (of the door) came apart easily by removing the screws for each section. The inside (broken glass) lifted out, was replaced, and the sequence was repeated in reverse. During the reassembly I was able to clean the other layers of glass that had gotten build-up on them over the years. Total time start to finish was about 30 minutes. Only tool required was a screw driver! Probably saved 100+ dollars!

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

Twisted replacement bulb into place easily. Let there be light!

It snapped right into the drawer, was very easy

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

The repair was simple - the knobs arrived in record time and were quick to replace. Pull off the old and slide on the new. Thank you PartSelect for the great service. A NJ customer.

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

First I removed the metal burner covers and then placed a thick towel over the top part of the oven to prevent scratching and in the event the glass fell, it towel would prevent breakage. I proceeded to loosen the screws holding the glides on both sides of the glass. The overhead glide attached to the upper oven bottom was the issue in extending the time to replace the lamp. All screws came out easily except one. One screw had become rusted from the moisture released during years of cooking. The head of the screw stripped inside the hole so I had to use a drill bit to loosen the screw. Due to dull drill bits, it took around 15 minutes before I was able to grip the head of the screw with a pair of pliers and screw it out. The treads of the rusted screw were undamaged so replacement would be no problem. The overhead glide hood was removed allowing me to remove the glass. The lamp was removed by a simple twist (flourescent bulb) and the replacement inserted with a half twist, a small click sound and a visual inspection indicated the lamp was installed. The overhead hood was reposition using two screws, one on each side. The glass was positioned to cover the lamp and the light switch was turned to the on position to test the light, the lamp turned on. Following the lamp test both side glides were fastened with all screws. The overhead hood was secured with the remainder of the screws. A new metal screw was used to replace the damaged screw. All the screws were checked and tightened where needed. The replacement knobs took seconds to install on the oven.