30-2246-00-01 Tappan Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jonathan from Arkport, NY
- Parts Used:
- 5303912606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My burners would not light. There wasn't the tell tale "click, click, click" of the spark module.
First I had to slide the stove out of its cubby and then I removed the two screws holding on the shield. I next removed the wires going to the spark module. I removed the top screw and loosened the bottom one. Installed the new spark module in reverse order. Less than 15 minutes for whole repair. Still have problems with spark module not working if oven is on, but I think it is because there is no air circulation behind the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Middle Village, NY
- Parts Used:
- 316035200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Two top burners would not light, defective switch
Warning- we found a lot of bare wires in this stove, check your wires before replacing the bad switches. I lifted the top, disconnected the power, pulled off the knobs, unscrewed the switch for the back light, removed seven screws to finally get the front panel off. Once you have the front panel off, changing the swich takes less than a minute. The switches just slide off the gas valve stems. Instructions show how to line up the new D-shaped switch mechanism to match the D-shaped shaft. Gently pull the two wires off the old switch and slide onto the new switch. Then put the panel back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from El Paso, TX
- Parts Used:
- 5303912606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
tHE ORIGINAL MODULE DIED AFTER 21 YEARS OF SERVICE
First had to move the stove out of its "nest", take the side cover off, remove 1 screw and loosen the other , take the old module out and reverse the operation. That simple.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue Z from Los Angeles, CA
- Parts Used:
- 316055800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grates were old and rusted and scratching the bottom of my pots
I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Len from Corry, PA
- Parts Used:
- 316035200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Switch plate cracked.
This hard to find GE part number was easy to find at PartSelect.com. The GE dealer said the part was permanently out of stock. Lift lid and remove a few screws and pull off two wires and replace switch plate and reconnect everything. Good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Bonita Springs, FL
- Parts Used:
- 318036310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs for the three timers on the appliance console deteriorateddue to age.
The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BUFFALO, NY
- Parts Used:
- 5303207048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wrong Part
I received the order in today's mail. However, the knob does not fit the thermostat port. I was excited the the knob you sent me looks exactly like my knob, However, The knob you sent me has a 1 at the port site. The knob on my stove has a 2 - it has a larger port opening.
Can this be remedied at all? Do you have a similar part with a 2 on the port hole?
Let me know if there is anything that can be done, Thank You.
Bob Alley
(716)875-1034 Landline
(716)367-8074 Cell
email: alleyoops2@verizon.net
Can this be remedied at all? Do you have a similar part with a 2 on the port hole?
Let me know if there is anything that can be done, Thank You.
Bob Alley
(716)875-1034 Landline
(716)367-8074 Cell
email: alleyoops2@verizon.net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from SPENCERPORT, NY
- Parts Used:
- 316035200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bad igniter in switch
Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from GLEN MILLS, PA
- Parts Used:
- 5303204154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rusted out front burner
remove screw, remove burner, install new burner and screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Hickman, NE
- Parts Used:
- 5303204154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gas burner went bad
I had the old burner already out, so all I had to do was insert tab into slot and then fasten with screw. Tried the burner and it worked, I just had to adjust the amount of air it received. Very satisfied with product and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paresh from La Palma, CA
- Parts Used:
- 5303912606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gas will not start
I unplugged the range. Opened the range by removing the burners. Removed exiting spark module then installed new one. Just make sure the four plugs are correct.
Was this instruction helpful to you?
Thank you for voting!