30-2247-23 (09) Tappan Range - Instructions

Warning- we found a lot of bare wires in this stove, check your wires before replacing the bad switches. I lifted the top, disconnected the power, pulled off the knobs, unscrewed the switch for the back light, removed seven screws to finally get the front panel off. Once you have the front panel off, changing the swich takes less than a minute. The switches just slide off the gas valve stems. Instructions show how to line up the new D-shaped switch mechanism to match the D-shaped shaft. Gently pull the two wires off the old switch and slide onto the new switch. Then put the panel back.

I first unplugged the power cord and raised the range top and shut off gas supply to oven. then i removed the broiler drawer. Then using the adjustable wrench i loosened and removed the gas supply line from safety valve. Then using the philips head screw driver i removed the 2 screws holding the heat sheild surounding the valve. Then i unplugged the 2 wires on the valve body. then i removed the 3 screws from valve bracket and removed the valve. Install in reverse order and adjust gas orfice for proper burner flame using adjustable wrench. takes about 30 mins. I have done this repair once befor so i kinda knew what i was doing from the get go!!!! I had the new part i had ordered from this site in just 3 days!!!

I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.

This hard to find GE part number was easy to find at PartSelect.com. The GE dealer said the part was permanently out of stock. Lift lid and remove a few screws and pull off two wires and replace switch plate and reconnect everything. Good to go.

I determined the safety valve must be defective. The model number of the Okeefe-Merrit/Tappan/Frigidaire/Electrolux stove (27 yrs old) could not be found online nor at Frigidaire's parts call center. However, due to Partselect's most helpful picture parts pages, I was able to find my valve with the part number clearly showing for me to see. No picture, no resolution. The info sheet with the part was beneficial and placement time was 15 minutes.

I raised the cook top and removed the fuse in the back, right corner and shut off gas at front left corner. After using meter to be sure there was no power, I marked the wires as front and back, disconnected them using needle nose, disconnected gas line using two wrenches, removed three screws in retaining bracket before sliding unit out. Installation was the reverse.

With fuse replaced before installation I measured 120 volts across the two wires. (Don't try to do it hot.) When attached to the valve the measure went down to 2.9 volts. After installation and all restored, it took about 1 to 1 1/2 minutes for ignition.

I may have saved myself the purchase of a new stove just now, but after 27 years I think she is going to want a new kitchen. It was worth the repair and Partselect was prompt with the delivery. Happiness returns to a disgruntled cook.

Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.

remove screw, remove burner, install new burner and screw

the gas control valve was removed ,then the igniter. The new part was plugged in and the valve was applied. It started right away. I want to thank the sales man, he sold us just what we wanted, not the one we thought we needed which was 240.00. My repairs cost $42. and a meal for my son and a friend. Would reuse this service again if needed.

took off the front panel where the burner nobs are was very easy

I had the old burner already out, so all I had to do was insert tab into slot and then fasten with screw. Tried the burner and it worked, I just had to adjust the amount of air it received. Very satisfied with product and quick delivery.