NE59M6850SS ((AA-00)) Samsung Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Uwe from FORT COLLINS, CO
- Parts Used:
- DE47-20037A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven shut off during self clean cycle and door stayed locked.
I took off the back cover after I looked at youtube similar problems. Then removed the little thermostat and un hooked the 2 wires. I looked up the part and after is was delivered couple days later I connected the 2 wies and after putting the back cover on the oven was back to normal. Was such an easy repair and the part was only $11.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from TROY, OH
- Parts Used:
- 3405-001034
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The microwave would not turn on or would run with the door open
Other tools that are usefull long needle nose pliers, long thin blade screw driver and small magnetic flashlight. Place the microwave on a work bench and remove the case it cover 3 sides. Place the microwave on a chair so it can stand with the controls up. You are replacing the lower door microswitch. The switch is located behind the control panel in the lower part of the area. The switch is several inches inside this area and your hands will not fit. Take care when moving wires and a couple of sensors. Use the thin blade screwdriver to release a tab holding the switch in place. Do not break this tab. Take the needle nose pliers and remove the switch. Put the wires on the new switch, open the door a short distance so a door lever moves enough to put the microswitch back into the bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from CHEYENNE, WY
- Parts Used:
- DG32-00002B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat consistently
My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the issue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from SEABECK, WA
- Parts Used:
- DG96-00110F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Upper Oven convection Fan making bearing failure noises
First remove the internal fan guard, (two Philips Screws). Holding the fan blade and using a nut driver (10mm?) attempt to carefully remove the nut off of the shaft. If it loosens with a counterclockwise rotation, it is a Right Hand thread, Part#: PS11720788. If it loosens clockwise, it is Left Handed and is Part# PS11720787. When the correct fan arrives, check to make sure it matches, then continue with installation.
TURN THE POWER OFF
Following the door removal instructions in the Owners Manual, remove both upper and lower doors. Remove the screws that go into the cabinet on the sides, I believe there are (6). The bottom vent cover is also attached with the bottom screws, so you can remove that and set it aside.
Get some help to assist you with moving the stove out of the wall cavity, it's not heavy, but awkward. I used a small furniture cart, and the second time I used blocking on the cart to raise it to just below the oven and was able to easily slide out/in.
Rotate the oven so you can visualize the back. There are two panels on the back to remove, Starting with the bottom one, remove the screws, (a couple in the middle too) and slide the panel up, (Tabs into a notch on the top of each side of the panel) The second panel comes off the same way, there may be some screws on the side and top you need to be aware of. Once you open the back, the fan that needs to be replaced should be identical. If you have already removed the guard and fan blade from the inside compartment, it should be a simple swap out.
Put it back together in reverse order, put power back on and check to see if it worked. If so, slide it back into the cabinet, be careful the flex conduit is aligned so it doesn't interfere. Second time around it only took me about an hour total and I didn't need assistance.
Fan works, Oven quiet, Happy Wife, Happy Life.
TURN THE POWER OFF
Following the door removal instructions in the Owners Manual, remove both upper and lower doors. Remove the screws that go into the cabinet on the sides, I believe there are (6). The bottom vent cover is also attached with the bottom screws, so you can remove that and set it aside.
Get some help to assist you with moving the stove out of the wall cavity, it's not heavy, but awkward. I used a small furniture cart, and the second time I used blocking on the cart to raise it to just below the oven and was able to easily slide out/in.
Rotate the oven so you can visualize the back. There are two panels on the back to remove, Starting with the bottom one, remove the screws, (a couple in the middle too) and slide the panel up, (Tabs into a notch on the top of each side of the panel) The second panel comes off the same way, there may be some screws on the side and top you need to be aware of. Once you open the back, the fan that needs to be replaced should be identical. If you have already removed the guard and fan blade from the inside compartment, it should be a simple swap out.
Put it back together in reverse order, put power back on and check to see if it worked. If so, slide it back into the cabinet, be careful the flex conduit is aligned so it doesn't interfere. Second time around it only took me about an hour total and I didn't need assistance.
Fan works, Oven quiet, Happy Wife, Happy Life.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from BOCA RATON, FL
- Parts Used:
- DE07-00130B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
clock flickering, really fast, part of time display missing numbers
removed back of oven plate, removed motherboard. then removed led display...............samsung said it was the mother board that made it due this, the motherboard was fine the display went bad
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SUSAN from DAVISON, MI
- Parts Used:
- DE60-30016A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Wrench set
upper fan motor bad
My repair went terrible as I was sent the wrong motor 2 times. My stove sat in the middle of my small kitchen for 2 weeks. Finally the 3rd was the correct one except I didn't have the right nut so I waited another day for that to be sent. Everything working good now, I just hope the bottom fan doesn't go out after this experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from SCHENECTADY, NY
- Parts Used:
- DE47-20037A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven wouldn’t heat to temperature after self cleaning
Pulled off the back panel (6 screws) thermostat was right there removed 2 wires and replaced with new put the panel back on done
Was this instruction helpful to you?
Thank you for voting!