NE58H9950WS (AA-02) Samsung Range - Instructions

I removed the control panel with a Phillips screwdriver and unplugged the burner switch and replaced the new switch and put the control panel back in place and turned on the burner and it worked as it should.i realized that I only would have only had to remove the 4 screws on the bottom of the control panel. All I would have had to do was just take those 4 screws out and remove the switch control knob and the two screws that held the switch in. Am very happy with the results

I took off the back cover after I looked at youtube similar problems. Then removed the little thermostat and un hooked the 2 wires. I looked up the part and after is was delivered couple days later I connected the 2 wies and after putting the back cover on the oven was back to normal. Was such an easy repair and the part was only $11.

Cool oven, open door. Turn off electrical power. I laid a cloth over door to protect and to catch ant screws that my fat fingers would drop. I removed 4 screws under control panel. I pulled panel up and off stove face. My wife held it safely as I removed the triple burner knob. I then placed new switch, on stove top in same position as old one. I then removed screws holding old knob to release from control panel. The removed electrical connections one at a time and installed on new switch. Reinstalled switch back in control panel. Reinstalled control panel. Placed knob back in place. Turned electrical power back on. Then tested burner. Wife is happy and so am I.

First turn off the breaker for your oven/range, then open the oven door and look up at the control panel where the controls are. There are four screws holding it in place. Remove them and wiggle the control panel away from the stove top. Before you remove the four wiring connectors from the old switch box take a picture so you will know how they go back on. Remove the wiring connectors and pull the control knob off its shaft. There are two screws behind the control knob that secure the switch box to the control panel. Remove them. Install the new switch box before attaching its wiring connectors which will make it easier to line up the screw holes behind the control panel.

Just a few screws hold on the faceplate beneath the switches - then the actuator just plugs in! Then replace the screws
For $185 and 10 mins I saved a $1500 range/oven.
Yay Partselect for having the part available:)

Other tools that are usefull long needle nose pliers, long thin blade screw driver and small magnetic flashlight. Place the microwave on a work bench and remove the case it cover 3 sides. Place the microwave on a chair so it can stand with the controls up. You are replacing the lower door microswitch. The switch is located behind the control panel in the lower part of the area. The switch is several inches inside this area and your hands will not fit. Take care when moving wires and a couple of sensors. Use the thin blade screwdriver to release a tab holding the switch in place. Do not break this tab. Take the needle nose pliers and remove the switch. Put the wires on the new switch, open the door a short distance so a door lever moves enough to put the microswitch back into the bracket.

Turned off circuit breaker, unplugged from wall. Removed dials from front of range. Removed back top panel, and removed Phillips screws holding the associated switches to the front panel. Installed new switches and moved the wiring connectors from old to new switches. Replaced the back panel and front dials. Restored power and tested. So simple even an old phone guy could do it…

Install handled by building engineer...thankfully. Did not take long for him, however, to install both sides of the drawer.

I had previously replaced the heating element and heat sensor to the range. The cost of replacing the thermostat was minimal. The key to replacing the thermostat is finding where it is located. Several videos describing the Samsung thermostat showed it housed under the top of the stove. This particular model places the thermostat at the back of the range near the left side. After unplugging the range, and removing the back cover with a Phillips screwdriver, it was easy to locate the thermostat. After unplugging the existing one, and using a very small flathead screwdriver to gently pry the upper and lower clips holding it in place, installation of the new thermostat was a breeze. Removing and replacing did not take more than a couple of minutes. The oven is now heating properly at all temperature settings. I would recommend finding a schematic of the range showing the location of all the parts before beginning the repair.

Pulled off the back panel (6 screws) thermostat was right there removed 2 wires and replaced with new put the panel back on done

My repair went terrible as I was sent the wrong motor 2 times. My stove sat in the middle of my small kitchen for 2 weeks. Finally the 3rd was the correct one except I didn't have the right nut so I waited another day for that to be sent. Everything working good now, I just hope the bottom fan doesn't go out after this experience.