FER300SX (XAA-01) Samsung Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Hooksett, NH
- Parts Used:
- DG44-01002A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dual burner only operates on high, no matter the setting
Followed video at the link below.
https://www.bing.com/videos/search?q=how+to+replace+infinity+switch+in+samsung+electric+range&docid=607999620772294704&mid=702E9DF006DF9B180DAA702E9DF006DF9B180DAA&view=detail&FORM=VIRE
https://www.bing.com/videos/search?q=how+to+replace+infinity+switch+in+samsung+electric+range&docid=607999620772294704&mid=702E9DF006DF9B180DAA702E9DF006DF9B180DAA&view=detail&FORM=VIRE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Uwe from FORT COLLINS, CO
- Parts Used:
- DE47-20037A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven shut off during self clean cycle and door stayed locked.
I took off the back cover after I looked at youtube similar problems. Then removed the little thermostat and un hooked the 2 wires. I looked up the part and after is was delivered couple days later I connected the 2 wies and after putting the back cover on the oven was back to normal. Was such an easy repair and the part was only $11.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- irene from MERIDEN, CT
- Parts Used:
- DG44-01002A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
front burner stayed on high
put in new dual element switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Edenton, NC
- Parts Used:
- DG44-01002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Heat element was always in high
Kill the power
Remove back of range
Pull off know and remove switch
Note the wire placement and wire the new switch
Mount new switch and replace back
Turn power back on
Remove back of range
Pull off know and remove switch
Note the wire placement and wire the new switch
Mount new switch and replace back
Turn power back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Tallahassee, FL
- Parts Used:
- DE47-20037A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Samsung oven was not heating properly. The oven baked at a lower heat (as much as 30 degrees) in the lower ranges of 350 to 450 degrees.
I had previously replaced the heating element and heat sensor to the range. The cost of replacing the thermostat was minimal. The key to replacing the thermostat is finding where it is located. Several videos describing the Samsung thermostat showed it housed under the top of the stove. This particular model places the thermostat at the back of the range near the left side. After unplugging the range, and removing the back cover with a Phillips screwdriver, it was easy to locate the thermostat. After unplugging the existing one, and using a very small flathead screwdriver to gently pry the upper and lower clips holding it in place, installation of the new thermostat was a breeze. Removing and replacing did not take more than a couple of minutes. The oven is now heating properly at all temperature settings. I would recommend finding a schematic of the range showing the location of all the parts before beginning the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jared from LAKE OZARK, MO
- Parts Used:
- DG44-01002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
You sent me the wrong part 2 times !!!!!!
You sent me the wrong part, and now I am getting the runaround
about sending the part back and to refund my money.
I am very disappointed with the way things are going.
Jared
about sending the part back and to refund my money.
I am very disappointed with the way things are going.
Jared
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from SCHENECTADY, NY
- Parts Used:
- DE47-20037A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven wouldn’t heat to temperature after self cleaning
Pulled off the back panel (6 screws) thermostat was right there removed 2 wires and replaced with new put the panel back on done
Was this instruction helpful to you?
Thank you for voting!