B9757*0 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Brecksville, OH
- Parts Used:
- 8053344
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F3 Error message
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru the back. If you don't you have a 15 minute job trying to fish the wires at an angle thru the insulation (a very frustrating task). Untie the string from the old and tie it securely to the new. Pull the string from the back and Voila! your new sensor can be plugged in or wirer nutted to the old connection on the back of the stove. Replace the nut and the two screws and you're done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Starla from Vashon, WA
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt out broiler element
Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Mill Valley, CA
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler wouldn't heat
First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from COTTAGE GROVE, WI
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broil Element Was Burned Out
1. Move oven out from wall 2. Remove back panel of oven, 8 screws 3. Remove 3 screws inside oven holding element 4. Pulled wire connections off of element 5. Reverse procedure to install new element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Manteno, IL
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The upper broiler element had burnt and broken into.
I must compliment PartSelect on their quick responce and delivery of the item ordered. It arrived a day after I had ordered it. Trust me, the $40.00 I spent on the item was way cheaper than having a repair service fix it or having the entire oven replaced. I would highly recomend anyone to utilize PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Corunna, MI
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken broiler top element
SUPER EASY! The part arrived very quickly. I turned off the circuit breaker, unscrewed the few nuts, pulled out the element and reversed the process. 'works beautifully! Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Atlanta, GA
- Parts Used:
- WP660579
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broiler unit would not heat
The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.
To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).
To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from OLIVE BRANCH, MS
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Top broiler element busted
Piece a cake!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myrna from Fowler, CO
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the top of baked goods were not baking
turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitchell O from Williamsburg, VA
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven not heating to set temperature
Removed the back access panel of the stove. Removed 2 screws holding the temp sensor, replaced temp sensor, Installed back panel. Done 19 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Mukwonago, WI
- Parts Used:
- 8053344
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Little or no heat when baking
That should have been an easy repair according to previous responders that replaced this part.
The first issue is the Phillips head screw that fastens the sensor to the back of the oven was frozen and I had to drill it out.
The second issue was I could not pull the connector through the hole where the sensor wires pass. I decided to cut the sensor wires and use wire connectors to attach the sensor as instructed in the sheet provided with the sensor.
NOTE: You MUST use third party "gray" colored wire connectors that you can purchase in a hardware store. - the connectors provided DO NOT have a metal insert and even after several attempts would not grab the wires.
Another caution is you should use a self-tapping sheet metal screw to fasten the sensor to the oven wall if you encounter the same frozen screw that I did!
After I installed the sensor I tested the oven but found that this DID NOT solve the problem! I needed to order the "hidden" bake element that is mounted under the bottom oven wall and also the broil/bake element that is mounted inside of the oven on the top. See my comments for the Bake Element (bottom)
The first issue is the Phillips head screw that fastens the sensor to the back of the oven was frozen and I had to drill it out.
The second issue was I could not pull the connector through the hole where the sensor wires pass. I decided to cut the sensor wires and use wire connectors to attach the sensor as instructed in the sheet provided with the sensor.
NOTE: You MUST use third party "gray" colored wire connectors that you can purchase in a hardware store. - the connectors provided DO NOT have a metal insert and even after several attempts would not grab the wires.
Another caution is you should use a self-tapping sheet metal screw to fasten the sensor to the oven wall if you encounter the same frozen screw that I did!
After I installed the sensor I tested the oven but found that this DID NOT solve the problem! I needed to order the "hidden" bake element that is mounted under the bottom oven wall and also the broil/bake element that is mounted inside of the oven on the top. See my comments for the Bake Element (bottom)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Parma, OH
- Parts Used:
- 8053344
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Bad tempature sensor
Followed instruction on web site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Parma, OH
- Parts Used:
- 8053344
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
F 3 error
I did the repair following your instructions and it went very well. Now the temperature is working good , but the oven is heating up very slow. So now what should I do to fix the oven?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Dacoma, OK
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element went out in my oven
Fast shipping and the part was very easily installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Richland Center, WI
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace bad broil Element.
First removed the oven door for easy access, removed two screws holding the element pulled old Element from back of oven to expose two connecting wires, disconnected wires and removed old Element. Connected wires to new Element pushed Element back into place and replaced two mounting screws put oven door back on, took about ten minutes. Very Easy!
Was this instruction helpful to you?
Thank you for voting!