Models
>
F9157*0
F9157*0 Roper Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for F9157*0
Viewing 8 of 8Keep searches simple, eg. "belt" or "pump".
$6.96
This chrome drip bowl is an OEM approved replacement part designed for use with various models of electric ranges and cooktops. This drip bowl fits under 6-inch burner elements and has a diameter of a...
In Stock
$10.88
The drip bowl is found underneath the burner element of ranges with a rolled terminal style plug-in surface element. The purpose of the bowl is to catch any drips or spills that may occur while cookin...
In Stock
This is a genuine OEM replacement part. This surface burner plug-in block kit is designed for use with surface elements of your ranges and cooktops. This kit helps connect the wire harness to the surf...
In Stock
$7.04
This tub spring is a genuine OEM replacement part for your washing machine and is sold individually. There are other names that the tub spring goes by, such as the suspension spring, balance spring, o...
In Stock
This 6 inch surface burner with reinforced delta frame carries 1250 watts and 240 volts. It has four turns and is compatible with many electric ranges. Its center medallion is all black in color.
In Stock
This temperature sensor is used with self cleaning ovens. Its 1000 ohm resistance increases with temperature. This sensor has male leads and comes with ceramic wire nuts.
No Longer Available
This electric range delta frame surface element with looped terminal ends measures eight inches and has five turns. It carries 2600 watts the center medallion is black in color.
In Stock
$85.65
The drum baffle lifts and tumbles the clothes inside the drum as the drum rotates during the drying cycle.
In Stock
$37.68
This push-to-start Robertshaw style replacement for load rated switches has a clockwise rotation. It also has a break off shaft, and comes with plastic adapters.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for F9157*0
Viewing 7 of 7Element will not heat
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/340571_1_S.jpg)
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/11757480_1_s.jpg)
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/373020_1_s.jpg)
How to fix it
Little to no heat when baking
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/388521_1_s.jpg)
How to fix it
Oven is too hot
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/388521_1_s.jpg)
How to fix it
Will Not Start
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/388521_1_s.jpg)
How to fix it
Leaking
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/11751118_1_S.jpg)
How to fix it
Shaking and Moving
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/11751118_1_S.jpg)
How to fix it
Oven not heating evenly
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/388521_1_s.jpg)
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Brecksville, OH
- Parts Used:
- 8053344
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F3 Error message
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the strin
... Read more
g still shows thru the back. If you don't you have a 15 minute job trying to fish the wires at an angle thru the insulation (a very frustrating task). Untie the string from the old and tie it securely to the new. Pull the string from the back and Voila! your new sensor can be plugged in or wirer nutted to the old connection on the back of the stove. Replace the nut and the two screws and you're done!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Parchment, MI
- Parts Used:
- WPW10250667
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
sounded out of balance even after shifting clothes
The tub was out of alignment and water fell behind it and onto the floor. My brother-in-law suggested my problem could be the tub balancing spring and when I moved my washing machine, there it was on the ground.
The schematic does not show where it hooks up. So after I did what I thought looked right, the machine still did not wo ... Read more rk properly. Then I replaced the three suspension springs and that didn't solve the problem.
I found a whirlpool "do-it-yourself" repair book at the library and was prepared to tear into the machine. However, I did not have the tub balancing spring in the correct spot at one end. It hooks up from one of the outer bracket to the back of the housing unit along between the legs. There is a hole that had rusted through. I simply drilled a new hole nearby and low and behold it works!
Easy fix - the frustration was with the poor schematic.
The schematic does not show where it hooks up. So after I did what I thought looked right, the machine still did not wo ... Read more rk properly. Then I replaced the three suspension springs and that didn't solve the problem.
I found a whirlpool "do-it-yourself" repair book at the library and was prepared to tear into the machine. However, I did not have the tub balancing spring in the correct spot at one end. It hooks up from one of the outer bracket to the back of the housing unit along between the legs. There is a hole that had rusted through. I simply drilled a new hole nearby and low and behold it works!
Easy fix - the frustration was with the poor schematic.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Malvern, AR
- Parts Used:
- 4391989
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Burner would not heat
First i shut off the power since this is an electric cook top/range. I then removed the knob and the two screws that hold the burner switch in place. I removed the wires one at a time and connected each to the new switch. I then reattached the screws to the switch. The most difficult part to me was breaking off the switch stem at the
... Read more
right level. I got that done and finally selected the appropriate adapter for the stem/knob fit.
Read less
Was this instruction helpful to you?
Thank you for voting!