FGP335VL2 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from Cumming, GA
- Parts Used:
- WP31939701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove Work But Your Oven Won't Get Hot ?
If your stove work's but your oven won't get hot it is your ignigter the ignighter in proper working condition sends a signal to the gas valve saying let the gas flow its ok. When the ignighter quits working it won't let the gas flow and your oven will not get hot. It is an easy fix. Just pull out all of interior parts the racks and the bottom heat shield the ignighter the white stone looking part that is screwed to the burner with two wires and it really don't matter what way the wires go back one of the wires connects in the back so you will have to pull the oven out. Now you have to clean under it and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MATTHEW from SAN CLEMENTE, CA
- Parts Used:
- WP31939701
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven would not light
Removed oven door and burner guard. Removed screws holding ignitor bracket and small panel beneath oven door. Disconnected ignitor wires behind panel and pulled out ignitor. Removed old ignitor from bracket and inserted new unit. Fed wires back down thru tubing and screwed in bracket. Connected wires and replaced panel. (Note: old ignitor glowed but would not pass enough current to operate gas valve)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lansing, MI
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Perth Amboy, NJ
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left rear burner would not ignite
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lake George, CO
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right front gas burner ignitor wouldn't spark
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Las Cruces, NM
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
two burner ignitors would not function on cook stove
1. ordered two new switches
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!