NEA3G8DX Norge Range - Instructions

I removed two retainer screws which released the outside panel.
Next I removed 2 screws which hold the middle glass pane from one of its retainer brackets.
The was another panel with 4 screws to remove before reaching the final glass inner assembly.
Once that panel was reoved with the broken glass it was time to put the repacement glass assembly back together.

The old gasket fell apart as I replaced the oven light and had to be replaced. That was very easy once I received the part. The spring broke on the oven door and had to be replaced. I initially tried to reach in from inside the pan drawer under the oven. That was impossible to reaach but it only took a few minutes to realize that I had to remove the side panel. I had to slide the range out from between the cabinets, but once that was done it was a relatively easy fix, without any special tools needed.

Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.

Purchased 2 piece broiler pan from this site

Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.

Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.

remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.

Before I give procedure steps, please note the following observations that I had.
a)If AC power is plugged in and an electrical terminal touches the frame, the resulting arc may require that you reset the GFCI or the circuit breaker.
b)The clock failed to run until it was properly mounted (including the back cover in place).
c)Movement of wires can cause them to work loose at EITHER end of the wire.
d)Attempting to operate the clock, Start and Stop knobs may extremely difficult or otherwise ineffective unless it is properly mounted. Fully depressing these knobs / shafts is difficult.

The numbered steps below are how I would do it correctly based on what i learned.
1)I unplugged gas range power cord.
2)Re-positioned range to access the back without damaging the flexible gas supply line.
3)Removed the rear cover (#2 Philips) behind the timer.
4)Verified no voltages present
5)Judged that the front cover glass needed removal - removed timer knobs and front glass cover
6)Removed existing clock timer by using a WIDE flat blade screwdriver to depress the rear of each clip and pushing the time our the front. Old part has damaged gears and one axle end out of position.
7)Fed old timer back through the opening to the rear to assist with transfer of wires.
8)With the assistance of a helper, transferred the wires one at a time from the old to the new timer.
9)Fed new timer back through the opening to the front; aligned and snapped into place.
10)Replaced front glass and knobs.
11)Plugged in AC cord (first did inspection for snug connections and potential shorts).
12)Tested buzzer feature of the timer. Unexpected that the buzzer was intermittent.
13)Unplugged power cord. Found & tightened loose connection - not at timer but other end of one of the timer wires at the chassis connection strip.
14)Reinstalled the metal back cover & plugged in the AC cord.
15)Set the timer start and stop times to one hour before present time. (Knobs need to be depressed.)
16)Set clock to present time by depressing the knob IN and rotating it clockwise to the correct time. As clock is manually advanced to the timer start and stop times, verified that each knob popped out. The hand on the clock for the timer moves also, but when you release the knob pressure, the knob pops out and then you set the timer past the buzzing to zero.
18)I put the oven through a self-cleaning cycle. This uses the new timer; starts when the START button pups out and stops when the STOP button pops out. Of course there are other controls you need to manipulate for the self-cleaning cycle i.e. CLEAN settings and the door lock.

I didn't. Don't know how to get to light bulb to change it for this specific model

I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Removed burnt bulb. On replacing the bulb I glued the bracket, retainer gasket and bulb cover together- I used only a small amount of glue-just enough to hold the three items together. You need to do this since the three items slip in your hand while you attempt to screw the bracket to the oven wall. Need my help, email me @ Lexidog999@tx.rr.com

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes