99B-4CX (1X) Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Salisbury, NC
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
heat element wouldn't heat after 30 years of cooking
Pulled screws loose from element, pulled old element out and replaced with new..really simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from cincinnati, OH
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower element in oven not heating.
Removed, tested and measured the old element. Got on line to find the part and ran across Part Select. Ordered and received the part in three business days. It was an exact fit and in good order. The total operation including removal and replacement of the element, locating and ordering the part only took about thirty minutes.....and that includes the ten minutes it took me to find my #2 Phillips screwdriver! : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrea from new york, NY
- Parts Used:
- WP7212P007-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A seal came off the oven
I found the model, ordered the new seal, it arrived very quickly via mail and I replaced the seal. You simply slid off the old, slid on the new one and hooked it in place. No expensive repairman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Park Ridge, IL
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Insulation along the top of the oven cracked and broke off
Took old insulation off and replaced it with new by hooking new part in its place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Abilene, TX
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element was corroding.
I turned breaker off for oven, removed screws from element mount, pulled the element out about two inches, then slid wire connectors up to unhook from element. Then set new element in, slid wire connectors on to back new element, then used pliers to make sure they were tight and secure by squeezing them, screwed element back in, turned breaker back on. Turned oven onto bake and left on for few minutes while it burned chemicals off element. Very simple!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Dequincy, LA
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element burned out
Removed old element with philips screw driver, reninstalled new element in reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from Georgetown, TX
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old lower element burned through, broke
found the element using visual grids supplied on the website. Measured old element and matched up with another after finding out that Whirlpool parts are interchangeable. Turned off power at breaker box. Replaced in 10 minutes.Fired it up to test at high temp for about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GERALD from HUNTINGTON BEACH, CA
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door seal badly deteriorated
The seal is suspended by metal clips at each end, which are inserted into holes in the oven box. The clips on the new seal were a bit too wide to fit into the holes. so I drilled the holes larger, and it worked fine.
Was this instruction helpful to you?
Thank you for voting!