CRG860A Maytag Range - Instructions

On this range, the switch at any one burner causes the igniters to spark on all four burners. However, there was no spark anywhere when I turned the knob for the front right burner. This indicated a fault in the switch on that knob. Very important to start by unpluging the power cord (I got zapped trying to skip that part!) Then remove all four burners, by turning them counterclockwise and lifting. Remove all igniter wires and set the burners aside. At the edge of each of the burner holes is a screw. Remove all four of these screws, then you can pry the cooktop up and remove it. Pull all four knobs off, and remove the four screws attaching the cover behind the knobs (two on top and two below (above oven door). This exposes the igniter switches. Slide the broken switch off the shaft, and remove the wires. (There is a small release tab at each pole of the switch. Depress it with a small screw driver and the wires can be pulled out.) Push the wires into the new switch, slide it into place, and put everything back together. Solved my problem!

Make a quarter turn counterclockwise, disengage a burner head, disconnect 2 wires, connect to a new head, install turn clockwise.

That's it!

Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.

unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.

Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.

Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

I removed all four burners and the ignighter wires. then I removed all the screws holding the burnner yokes to the top of the stove. removed the top of the stove and replaced the new fetting. Replaced everything and fired it up. All went well.
Most impressed with the PartSlect web site. the ease of navigaation and the blow up that inabled me to find the part and part number. Ordering was easy and delevery was quick
Thank You.
Kareem.

The burner was leaking a rust colored dirt and shooting flames all over the place. The top came off and I needed channel-locks to get the bottom half out. The wires were hard to get off and I broke one connector off so I soldered the wire on to the new part which fit the stove top perfectly. It still took less than a half hour to replace. Without problems it should take about 5 minutes.

The old burner head had corroded allowing gas to come out at the bottom. The actual replacement is just turning the head, lifting it out, transferring two wires with slip-on connectors from the old burner to the new one, and dropping the new one in place. Most of the time was spent sanding away corroded metal on the base to make a good fit. The information on the burner head says that the company has decided not to use a gasket under the head. I suggest that was a bad decision.

Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.

Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.

Replaced with a new one.

Overall, it was painless and easy with zero problems

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.