Models
>
26AA-6CLX
26AA-6CLX Maytag Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This chrome drip bowl is an OEM approved replacement part sourced directly from the manufacturer. Drip bowls are a part for your cooktop, positioned underneath the burner to catch spills. This drip bo...
In Stock
This genuine OEM kit includes the parts required to replace a surface burner receptable on your range. The kit comes with a plastic block, a metal bracket, high temperature wire nuts, and wires. The b...
In Stock
NOTE: The manufacturer recommends that you replace the burner receptacle at the same time.
In Stock
The manufacturer suggests replacing the receptacle at the same time.
In Stock
This spade style bake element with push on wire terminals is 15 inches long and 19 inches wide. The depth of the terminals is three inches.
In Stock
This oven broil element with push on terminals can be used with some electric ranges or ovens. It comes with four screws and an instructions sheet. This element also has a terminal depth of three inch...
In Stock
$71.04
This oven door seal is seventeen and a half inches long. It is made of rubber and has a metal hook on either end to hold it in place. This seal sits on top of the glass window pane.
In Stock
The surface element control switch turns the surface element on and off and controls how much heat the element produces.
In Stock
In Stock
$111.51
This kit includes two 8" elements, two 6" elements, four receptacles and any remaining hardware needed for installation.
In Stock
This oven door seal is fifteen and a half inches long. It is made of rubber and has a metal hook on either end to hold it in place. This seal sits on top of the glass window pane.
No Longer Available
The hinges allow the door to swing up and down. The hinges must be properly adjusted in order for the door to close properly.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 26AA-6CLX
Viewing 4 of 4Element will not heat
Fixed by these parts
How to fix it
Little to no heat when baking
Fixed by these parts
How to fix it
Little to no heat when broiling
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Carthage, NC
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister ... Read more 's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
My sister ... Read more 's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
Read less
Was this instruction helpful to you?
Thank you for voting!
1 had 2 large burners not working at all, and was cooking everything on the 2 smaller burners
It was so simple to repair - all I had to do was slide the older burners out and slide the new ones in - it took less than 10 min to complete the whole job! No tools used at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from Hudson, CO
- Parts Used:
- WPY04000041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element burned out
Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
Was this instruction helpful to you?
Thank you for voting!