Models > 38H-3T

38H-3T Maytag Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Long Oven Sensor – Part Number: 12001656
$42.18
This is a factory-certified oven sensor kit with two harness adapters. Its purpose is to sense the temperature inside the oven. Replacing this part can fix an oven that is not reaching the proper temp...
In Stock
Order now and your part arrives by Mar 19
Range Terminal Block – Part Number: WPW10245259
$26.73
It provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
In Stock
Order now and your part arrives by Mar 19
Oven Door Spring – Part Number: WP7803P058-60
$14.65
This oven door spring is six inches long, and is made of metal.
In Stock
Order now and your part arrives by Mar 19
Bake Element (15 Inch long x 19 Inch wide) – Part Number: WPY04000041
$77.95
This spade style bake element with push on wire terminals is 15 inches long and 19 inches wide. The depth of the terminals is three inches.
In Stock
Order now and your part arrives by Mar 19
Oven Door Gasket – Part Number: 7201P036-60
No Longer Available
Hinge - Left Side – Part Number: 3418A029-34
The hinges allow the door to swing up and down. The hinges must be properly adjusted in order for the door to close properly.
No Longer Available
Hinge - Right Side – Part Number: 3418A030-34
The hinges allow the door to swing up and down. The hinges must be properly adjusted in order for the door to close properly.
No Longer Available
Electronic Relay Board – Part Number: WP7428P005-60
This board sends information (such as temperature of oven, bake, broil) to the main control board during specific functions.
No Longer Available
Broil Element Kit – Part Number: WPY04000042
This broil element is a little over seventeen inches long, and is not quite thirteen inches wide. It has screw on terminals and a terminal depth of just over three inches. The terminals are just two i...
No Longer Available
Power Cord – Part Number: PT220
$26.20
In Stock
Order now and your part arrives by Mar 19
DISCONTINUED – Part Number: 7902P275-60
No Longer Available
Power Cord – Part Number: PT500
$34.97
Special Order
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for 38H-3T

Viewing 10 of 10
Little to no heat when baking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Oven is too hot
Fixed by these parts
Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing
How to fix it
Oven not heating evenly
Fixed by these parts
Fixing Fixing
How to fix it
Element will not heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Touchpad does not respond
Fixed by these parts
Fixing Fixing
How to fix it
Will not program
Fixed by these parts
Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing
How to fix it
Door won’t open after self cleaning cycle
Fixed by these parts
Fixing
How to fix it
Little to no heat when broiling
Fixed by these parts
Fixing
How to fix it
Replacing the Long Oven Sensor

Replacing the Long Oven Sensor

Replacing the Range Terminal Block

Replacing the Range Terminal Block

View More
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from Westford, MA
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read less
162 of 213 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
charles from marstons mills, MA
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
F1-1 code
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa ilure to do so will cause the plastic plug connector to melt from oven heat.
Read less
79 of 110 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Decatur, GA
Parts Used:
WPW10245259
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set
Burned terminal block and filter board
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
95 of 204 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More