35EA-7 Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anita from Hudson, CO
- Parts Used:
- WPY04000041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element burned out
Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Morganton, NC
- Parts Used:
- WPY04000048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Broiler unit would only heat on one side
Removed the screws that held the element and disconnected it. Placed the new element in the proper place, connected the wiring, and replaced all the screws. The unit worked beautifully, and all is well. My wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from San Rafael, CA
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replacement of broil element in wall oven
In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw driver is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bellefonte, PA
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not work
slide stove out unplugged it took six screws out put new one in transfered wires pluged back in and it works thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from South Bend, WA
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
A switch on a front burner went out
I first removed the back panel that covers the switches from back of stove; then I removed the wires and put them on the same numbered wires on the new switch; put the new switch in place with the wires connected to it; installed the 2 front screws and put the back cover on again & it took about 10 min and saved about $300.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rolland from New Port Richey, FL
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Broiler element split after oven self-cleaning
We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Reston, VA
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replaced Broiler Element
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Hughes Springs, TX
- Parts Used:
- WPY04000035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not heat.
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alex from huntington, NY
- Parts Used:
- WPY04000048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace element
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Thornton, TX
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element burned out, broke circle, heat only half
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Elba, AL
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burnt out
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from SHOW LOW, AZ
- Parts Used:
- WPY04000035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
ELECTRIC BURNER SUPPORT FELL OFF AND BURNER SOMETIMES WOULD NOT COME ON.
Stuck the new one into the plugin.
Was this instruction helpful to you?
Thank you for voting!