Models > FG4114ES > Instructions

FG4114ES LG Range - Instructions

Jump to:

All Instructions for the FG4114ES
1 - 6 of 6
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jeffrey from CERRITOS, CA
Parts Used:
4890W1N005A
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Replace Inner Oven glass because it shattered
Go onto youtube, such as https://www.youtube.com/watch?v=-ITkrwhDNMQ and watch similar videos for DYI. The process is very similar to other models.

Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know the process of where each screw goes when you re-assemble.

Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)

Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.

Hope this helps
9 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Martin from KEWASKUM, WI
Parts Used:
MEE61841401
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven wouldn't ignite
Took off the oven door then took out the racks and two screws in the oven bottom and removed it . Then removed the heat deflector. Then un plugged the old igniter and removed the burner to make it easier to remove the old igniter. Then installed the new igniter and reversed the process
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sheila from HOPKINTON, MA
Parts Used:
MEE61841401
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Oven would not light
As soon as my husband put it in the oven, the very thin prongs broke. There was no guard on either side of the prongs for protection like the one that had been in there. Very costly to us of $185 with no fix. Very disappointed in that ignitor. It would have been an easy fix. Had replaced one previously but it only lasted 6 months. Now we have a new stove
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Sierra Vista, AZ
Parts Used:
MAM63404404
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven base coating melted in the center of the base
Removed two screws at the rear of the oven with a phillips screw driver. Removed door to get the base out. Installed new base and door.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
K R from BOISE, ID
Parts Used:
4778W1N001B
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Broken front leveler
This is a very simple repair of remove and replace. You do have to lay down the range to make it easy.
4 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
rorke, from tarzana, CA
Parts Used:
MAM63404404
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
melted foil on the base pan in the oven
i removed the oven door by lifting the safety latches on each hinge and gently lifted the door off. once off i could access the 2 large phillips head screws and loosened and removed them. then i simply slid out the old and slid in the new & reversed the process.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FG4114ES
1 - 6 of 6