Models
>
LRE3083ST
LRE3083ST (00) LG Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for LRE3083ST
Viewing 5 of 5Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
$6.29
This Fuse protects the microwave from damage by shutting off the microwave if there's a power surge.
High-voltage capacitors can retain a lethal electrical charge even when the microwave is unplugged,...
Special Order
In Stock
In Stock
$103.04
This part is the replacement A/C fan motor or convection fan motor for your range. It is used to spin the fan blade, which circulates hot air through the oven, and ensures even heating. If you notice ...
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for LRE3083ST
Viewing 7 of 7Little to no heat when baking
Fixed by these parts


How to fix it
Won’t turn on
Fixed by these parts


How to fix it
Element will not heat
Fixed by these parts


How to fix it
Oven not heating evenly
Fixed by these parts


How to fix it
Oven is too hot
Fixed by these parts


How to fix it
No heat
Fixed by these parts

How to fix it
Door won’t open after self cleaning cycle
Fixed by these parts

How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
-
Customer:Richard from CHESAPEAKE, VA
-
Parts Used:MEE62385201
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Hammer 1, Glass range top and heating element 0
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution:
1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet.
2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet.
2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Jack from LEXINGTON, KY
-
Parts Used:MEE62306405
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Bottom heat element went out
Checked element no reading. Took off back panel and removed element. Took 5 days to get element. Put in new one. Took 20 minutes. Did not have to cut panel as video had shown. It had screws and was easy to get out and put the new one in. The new element was exactly the same as the old one. I checked all elements before ordering. Was satisfied with everything but the delivery time
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Norman from ST PETERSBURG, FL
-
Parts Used:AGU73969710
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Plate Assembly Replacment
1. Unplug the stove (you will need 1 person to assist).
2. Remove the 3 assembly screw (Philips screws) located underneath the front of the assembly, near the oven door.
3. Raise the plate assembly to expose the heating elements (Take a photo of the positioning for installation reference).
4. Remove the wires connected the heating elements (unclip the connectors only).
5. Remove the holding clips from the heating elements (2 clips on each elements, the large element has 1 clip and 1 screw).
6. Remove the elements only (leave the wires in place).
7. Remove the Plate Assemble (save the 2 black rubber mounts located on the sides, the new assembly dose not come with replacements) .
8. Now your are ready to reinstall the Plate Assembly, so do the reverse and you should have no issues (check your photo for proper installation).
2. Remove the 3 assembly screw (Philips screws) located underneath the front of the assembly, near the oven door.
3. Raise the plate assembly to expose the heating elements (Take a photo of the positioning for installation reference).
4. Remove the wires connected the heating elements (unclip the connectors only).
5. Remove the holding clips from the heating elements (2 clips on each elements, the large element has 1 clip and 1 screw).
6. Remove the elements only (leave the wires in place).
7. Remove the Plate Assemble (save the 2 black rubber mounts located on the sides, the new assembly dose not come with replacements) .
8. Now your are ready to reinstall the Plate Assembly, so do the reverse and you should have no issues (check your photo for proper installation).
Was this instruction helpful to you?
Thank you for voting!