MS95MT ((HSLEGSS)) LG Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jimmy from OZARK, MO
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
One of the switches in a component that door activates when shut.
I replaced the whole component with all three switches in it even though only one switch was bad . Taking out one switch out of the holder unit would probably have damaged the unit that was holding the switches. Easy install and it works great again .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from VIRGINIA BCH, VA
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
would not start.
diagnosed defective 'door-shut switch' in the switch holder assembly. rather than replace switch, replaced entire locker holder assembly which made for a very simple and easy repair...not to mention very inexpensive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Philadelphia, PA
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave not heating, everything else works
Not knowing which of the switches to replace I ordered all three in the assembly. Replacing the full assembly was easy, first unplug the microwave. Then remove the top cover to access the screws that hold the control panel in place and let the control panel hang. There are two screws that hold the assembly in place - remove those. I used needle nose pliers to pull the wires off of the switches and immediately put the wires on to the new assembly so there was no confusion on what wire went where. Place the assembly back in position, replace the two screws to hold it in, put control panel in place and secure screws. Replace top cover and plug in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from LUXEMBURG, WI
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The over the stove microwave door would not close.
I unplugged the microwave. I did watch a YouTube video to see how the plastic frame around the door could be removed. I used a putty knife to pry it off. The spring was still in good shape, so I hooked it up to the new latch/locker part and onto the microwave. This was just a little time consuming because I was trying to be careful so I wouldn't break anything on the new part. The plastic frame clicked right back on. I plugged the microwave in and it worked right away. If I can do it, you can do it. Sure beat buying a new microwave. Great experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SEVERN, MD
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
food does not get hot, carousel did not turn, all other indicators worked
Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from SUPERIOR, NE
- Parts Used:
- 5889W2A005J
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Turntable rolloers
picked up turntable plate (glass), removed broken part, placed new part
in position and replaced the glass plate.
less than one minute
in position and replaced the glass plate.
less than one minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from DELAND, FL
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave door would not shut completely and would not activate switches
After checking all three switches for continuity I determined that the plastic door lever had warped or gone out of wack. After shutting off power at the breaker box I removed the door, the inside trim piece around the inside of the glass. Removed the black two prong door lever, reattached the new door lever and then reinstalled the trim piece and all screws. Works fine now. Easy fix just make sure your switches are all ok then replace the door lever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from FOREST, VA
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door locker snapped off
Unplugged the microwave. I opened the door. I used a butter knife to pop the bezel off the inside of the door. I pushed the locker up and to the left and used the butter knife to pry it loose. Disconnected the locker from the spring, and reversed for the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from MILLINGTON, TN
- Parts Used:
- 3500W1A013R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Micro Wave no heat all else fine. Also at times door would not shut properly.
Replace (after testing w/ohm meter) diode and locker holder. My door often would not close properly. Microwave let know by saying not shut properly. When disassembled found the top screw mount was hollowed out resulting in it moving on occasion when you close door. First remove casing (special safety torx head) needed for rear screws. Onc e removed all parts available to view or work on. Diode is on the capacitor so caution is needed when removing. Serious shock hazard if touched. Use insulated pliers to remove from capacitor and a phillips on the ground. Test with ohm meter Should have resistance on way and non the opposite. Replaced mine bad. Next the holder 2 phillips screws and its yours. Unplug each switch and remove. Take note to what wires go to what switch and what switch mounts where. Mine had 3 switches. Removed from old holder and put in new. Screwed holder back in place and left scrws loose till re wired. Once wired set the holder by lightly tighting the screws. Try the door till it seats properly ensuring that all 3 switches are working properly. If so thighten screws. If all seems to work as advertised, safely plug in and test unit if heats up un plug and put cover back on micro. Your all set. Happy heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PURCELLVILLE, VA
- Parts Used:
- 4370W1A006B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The new part was too thick for the worn out plastic ring which is obsolete.
Needed to raise the part to match the ring. I used peanut butter to hold plastic shim while replacing to hold it in place. Built in Oct. 2009.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dick from SANDY, UT
- Parts Used:
- 6600W1K001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave fan would come on when door open. Timer and unit would not switch on.
I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.
https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni bc from PORT ORANGE, FL
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch broken... Spring off
You Tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from TECUMSEH, MI
- Parts Used:
- 5889W2A005J
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
one of the little wheels kept coming off the ring.
just lift the glass turntable off and take the ring out and put the new in and put the glass back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cesar from Miami, FL
- Parts Used:
- 4370W1A006B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shaft socket was worn out
Pop old one out and replaced it with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg J. from WEST CHESTER, PA
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Latch spring keeper broke
Removed door from microwave and then popped the inside widow trim ring off. Removed 4 screws from the window bracket, replaced the latch with a new part and then assembled.
Was this instruction helpful to you?
Thank you for voting!