79095742991 Kenmore Range - Instructions

First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the different sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

All the was needed was a Phillips screw driver. It's not difficult. Watch out because the door is spring loaded and does seperate quickly after all the screws are out. Be sure to watch the front panel, it appears to be heavy glass and can come out of the slots during the repair. I only had to re-assemble and dis-assemble 4 times before I got it right but it's still fairly easy to do if you take your time.

Remove old element by removing two screws on back wall of oven, pull attached wires out about 6" and disconnect. Reverse to install, very easy. Of course the oven door makes it harder to get at things, but it all worked out. Partselect was the only place I could find the element since the stove is 18 years old. I love keeping appliances going as long as possible.

Pulled out the stove, removed the screws that held on the back panel, took out the 2 screws that held in the element and disconnected the wires and put the new one in. I put the screw back in and was finished!

I pulled the old switch out, took off the two wires, put the two wires on the new switch and pushed the switch back in place.

My husband opened the oven door.He removed the metal strip at the top just under where the knobs are.I held the top of the stove up while he unscrewed the 2 screws on either side of where the knob goes and he unplugged the connectors on the switch assembly one at a time a reconnected the new ones. We slid the post through the hole and lined up the two holes put the screws back in. Walah. I cont. holding up stove he got a socket to unscrew the strip holding the back elements in place. He undid just the one side used pliers to squeeze clamp together pushed the little post through the slot....unplugged the connectors keeping track of them. He used a screwdriver to unscrew clamps to screw them onto the new element at the same number as he took them off the old element. We popped the new element back in hooking up all connectors poked the little clamp posts through the holes attached the screw that is the strip holding elements in place. We closed the stovetop We lined the metal strip up at top of oven door underneath the knobs and put the 4 screws back in and closed the door. Done. I would say it took maybe 30 min.if that. Works like a champ.

i had to remove all the broken glass then removed the metal that was holding the glass. set the new glass in the metal strips and screwed it back togethr. i also had to remove the frame from the door in order to get to the inside glass. then i had to put the door back together.

The repair was fairly easy. The oven door was attached to a spring arm that had one screw holding each arm to the door. Once off, the outside set of screws were removed and saved in a small dish. Each section had 6-10 screws, to it's best to keep each set separate from each other. Each of the three layers (of the door) came apart easily by removing the screws for each section. The inside (broken glass) lifted out, was replaced, and the sequence was repeated in reverse. During the reassembly I was able to clean the other layers of glass that had gotten build-up on them over the years. Total time start to finish was about 30 minutes. Only tool required was a screw driver! Probably saved 100+ dollars!

Very important first step: Turn off the circuit breaker for the range or disconnect the power cord.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil element. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.

I must say that I am very pleased with speed of your part delivery, I have to ad that the first part I received was defetive, the inner element was open and therefore it was not working, I called back and a very curteous person took care of the problem, I got a replacement part 2 days later and now all is OK.
Very good service indeed,
Thank you.

I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!

It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!

Removed screws. Unplugged temp sensor. Put screws back in. So easy a caveman could do it.

I looked up the error code on line and found it was likely a faulty oven temp sensor. I was able to find the part and diagram at partselect.com and placed an order. The probe was in stock and arrived within a couple days. The repair took only about 20 minutes and works fine now. Thanks for your help partselect.com!
Jim