Models > 1439007100

1439007100 Kenmore Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for 1439007100

Viewing 6 of 6
Body Assembly Diagram and Parts List for Kenmore Range
Body Assembly
Compartment And Oven Door Assembly Diagram and Parts List for Kenmore Range
Compartment And Oven Door Assembly
Cook Top Assembly Diagram and Parts List for Kenmore Range
Cook Top Assembly
Pan And Ring Kit Diagram and Parts List for Kenmore Range
Pan And Ring Kit
Rotisserie Kit No. 8007130 Diagram and Parts List for Kenmore Range
Rotisserie Kit No. 8007130
Upper And Lower Control Panel Assembly Diagram and Parts List for Kenmore Range
Upper And Lower Control Panel Assembly
Keep searches simple, eg. "belt" or "pump".
Agitator Assembly – Part Number: 285574
$156.71
Does not include softener dispenser. **** Some assembly required.****
In Stock
2-Speed Drive Motor with Jumper Wire – Part Number: 12002353
This two speed split phase washing machine motor performs 1725 revolutions per minute in one speed and 1140 revolutions per minute in the other speed. This motor runs at 1/2 horsepower and it carries ...
No Longer Available
COS-EXP CRATING – Part Number: 5217
No Longer Available
SUB 4360 – Part Number: 4024
No Longer Available
SUB 31952 – Part Number: 4074
No Longer Available
STRIKE ESCUTCHE – Part Number: 4091
No Longer Available
CODE J – Part Number: 5241
No Longer Available
CODE J – Part Number: 4071
No Longer Available
Guide rail – Part Number: 4036
No Longer Available
Rear cabinet – Part Number: 4037
No Longer Available
Bag holder – Part Number: 5324
No Longer Available
Bushing – Part Number: 5306
No Longer Available
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for 1439007100

Viewing 1 of 1
Will not agitate
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Nora from Marshall, TX
Parts Used:
285574
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Agitator wasn't spinning well
First I removed the screw that held it in place with a socket. The agitator became loose and easy to remove at this time so I lifted it from the washing machine. I then just placed the new agitator in place and replaced the screw being careful not to do it too tight. The replacing of this part was an easy job and thanks to Part Select it saves me hundreds of dollars.
Read less
26 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Matt from Oxford, GA
Parts Used:
12002353
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
Motor Froze
Make sure to release the springs and pulleys before you try to tackle the bolts that hold the motor base to the bottom of the washer. Mine were a bit rusty and took some force to break loose. Also it's a good idea to take pictures of how everything sits before you disassemble as the pictures in the repair kit are not very clear. Oth er than that it was pretty straight forward. Wiring was a breeze. . . . Good luck
Read less
22 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
walter from watertown, WI
Parts Used:
12002353
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Socket set
the motor burnt out
took washer into the garage, removed front cover & disconnected the wiring. Then i removed the motor assembly. Piece of cake to finish job.
17 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More