79072802011 Kenmore Range - Instructions

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet metal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Replaced the probe because that's what this site recommended.The oven still does not heat up.

took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.

First, remove the warming drawer. This allows access to the igniter's plug. Unplug the igniter. The rest of the job is performed within the oven. Remove the bottom (1/4 inch socket). Then remove the next, v shaped piece. The igniter is bolted to the aerator. Remove bolts, and it pulls right off. Reverse these to install new igniter.

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

Turned off electric,removed rear panel and replaced part.oven is now operating good as new.

Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.

move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps

First I removed the two screws that hold the bottom panel I then pulled the panel out and put the new panle in and put the two screws back in

Oven ignitor is on the bottom gas unit. Ignitor is in oven and plug is in warmer oven on left wall at very back of warmer oven. It has duel function to light both upper and lower gas burners (in oven). Wires of new plug that I received were shorter than existing wires and would not reach the plug from ignitors center mount location to plug at far back of warming unit on left wall. Even if the wires would have been long enough, I couldn't figure out how to "release" the existing plug. Easy solution: Cut old wires at junction of old ignitor (leaving wires as long as possible). Cut new wired as close to new male plug as possible (leaving wires as long as possible on new ignitor). Strip ends of old and new wires and wire nut with porcelin wire nuts (hardest part of job was locating porcelin wire nuts)! After placing wires out of the way of burner and ignitor, reassemble stove parts. AVOID touching new element as oil from hands will decrease the life of the element. Good Luck..

Tore the oven apart and replaced the igniter, then put the oven back together. Perhaps if Frigidaire manufactured an appliance that lasted longer than three years this wouldn't have been necessary. This is the second Frigidaire range that only lasted three years. Believe, the next stove we buy will definitely not be a Fridgidaire!

I "You Tubed" disassembly and commenced by disconnecting electric power. Removed door via You Tube instruction, removed back panels of unit, and replaced the oven temp probe. Easy Peasy. Then removed bottom of oven, next level above the burner and started to remove the igniter. One nut refused to be removed so I removed the burner and cut the nut and drilled it out. I reinstalled the new igniter with a metal screw from the rear panel and reinstalled the burner. Through the tiny hatchway I reconnected the new igniter and reassembled the oven to test. Just fine heated to 350 in 7 minutes. Awesome. Then, I called my brother, Pat, to give his imprimatur to the hillbilly nut switch. He said ok, I am done.

To any reading this, I would order the igniter and the burner at the same time. That tough nut cost my one extra hour.

I ordered the replacement igniter for the oven portion of the unit from Part select. It shipped very quickly. Upon receiving the igniter it was time to get to work. It took roughly 10 mins to replace and we were back up and running.