36261748001 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from North Prairie, WI
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner bowls needed replacement
Very easy repair, Pulled burner coil out, removed old burner bowl. Put in new burner bowl, plugged burner coil back in... easy as 1,2,3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Knoxville, TN
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Bowl Needed Replaced
Removed burner element and put in bowl
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Nassau, NY
- Parts Used:
- WB44K10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Lower bake Element would not heat.
First I slid the stove out and unpluged it, then removed two screws,slid out element, disconected two wires, slid new element in to place, pluged two wires in ,put into place and installed two screws, pluged stove back in, and turned on to try. Works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Americus from Pittsburgh, PA
- Parts Used:
- WB17T10006, WB31T10011, WB31T10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burned out block
Watched a repairman do it the last time for $200.00. This time I unplugged the stove, unscrewed four screw nuts holding the upper rear cover, unplugged old wires, reconnected new ones, fed them thru to the front, attached them to the new block, screwed the block into place, replaced back cover, stuck the element into place, made my little brother plug it back in and turn it on first. It worked. Cost me $20.00 to do what the repairman did the last time. I also replaced the reflector pans. No-brainer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Mt. Vernon, IN
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The Bake-o-lite (Hard Plastic) block that holds the burners female connection in place had chipped away over time and wouldn't allow the male part of the burner to connect up correctly.
After unplugging the range I took the rear sheet metal panel at the top off with a nut driver to expose the wiring connections. The next step was to remove the single screw holding the old part in place. (under the drip pan) Once free I snipped the old part from the wires and then taped the new female ends to the old wires with black electrical tape. From rear I carfully pulled the old wires through the back until I could reach the new wiring connections. Unplugged old, plugged in new and replaced the rear metal cover. Then I put the screw that holds the new block bracket in place, replaced drip pan, and burner. The final step was to plug the range back in and check to see if the burner worked. It did and I was done. Approx. 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Tewksbury, MA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The stove's bowl were burned and a mess.
Pulled out burner and put new bowls in. Looks like a new stove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Eowell, OH
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced old drip bowls
Took 5 minutes to replace the 4 bowls. Ordered the bowls one day & they arrived the next day All went perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from anna, TX
- Parts Used:
- WB44K10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Broken heating element
1)Turn off power to stove
2)remove 2 bolts holding heating element
3)pull element out of the back of the oven about 8" so that the wire connects is visable
4)pull wire clips off of heating element and remove element from the oven
5)put wire clips on the new heating element
6)push new heating element back into the holes in the back of the oven
7)screw botls back into the oven holding the heating element in place
8)Turn power back on
2)remove 2 bolts holding heating element
3)pull element out of the back of the oven about 8" so that the wire connects is visable
4)pull wire clips off of heating element and remove element from the oven
5)put wire clips on the new heating element
6)push new heating element back into the holes in the back of the oven
7)screw botls back into the oven holding the heating element in place
8)Turn power back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- douglas from louisville, KY
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
burner was shorting out
unplugged unit pulled it away from wall took off the backplates traced wire to plug replaced with part ordered very smooth operation. the most impressive thing to me was i ordered part on computer and it was at my door in 30 hours awesome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from las cruces, NM
- Parts Used:
- WB25T10041, WB24T10027, WB24T10022
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Switch and burner dead
Removed rear panel, disconnected wires, unscrewed switch X2 - installed new parts in reverse order. Note: Would have appreciated new mounting screws with replacement switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Pottstown, PA
- Parts Used:
- WB57K2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
the glass oven door broke after being accidently hit
Removing all the shattered glass was endless it seemed. hovever the repair was very easy. Even for a very busy stay at home mom with limited handy man skills.I did it and it only took about 15 to 20 mins. once i got all the glass out of the way.I untightened the 4 sm.bolts under the door just enough to fit the glass in and when in place retightened the bolts and done !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ellen from centennial, CO
- Parts Used:
- WB44K10002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broiler burnt out.
Removed screws using nut driver. Pulled element way forward until wires came through. Pondered how to detach burned out element from wires. Chickened out, call neighbor who grasped things firmly with two hands and pulled. Old element came loose. Popped in new element. Cursed the screws that wouldn't align with holes to support element; finally did it. Screwed element plate in place. Put oven door back on, plugged it in and turned it on hoping that we hadn't reversed the wires. Job accomplished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Salem, IA
- Parts Used:
- WB44K10005
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven Element had burned out
My husband did it, we unplugged the stove first then he removed the damaged element replaced it with the new plugged it back in and we were in buisness. I like that this was an acutual part for my stove(not some universal thing) and it arrived very quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Yorkville, IL
- Parts Used:
- WB57K2, WB07K10121, WB07K10120
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Glass broke due to falling over.
Glass was a little messy cleaning up but removal and placement of new glass and side rails went easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Houston, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven rack missing when I purchased the house
I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.
Was this instruction helpful to you?
Thank you for voting!