62920245 Kenmore Range - Instructions

Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.

Just placed it at the filter location. Liked the ring feature on the filter for ease of removal for cleaning. My previous ones didn't have such feature. Thank you for filling my order. I bought an extra filter for the future. I'm a big user of my Jenn-Air range. I may soon be needing to replace my griddle. Will be contacting your company then.

I simply lifted off the grille in the center of the stove, pulled out the old filter and dropped the new one in. It sits at an angle (right side down, left side up) rather than slotting in to a particular spot.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

I removed three screws, pulled the element out from the rear wall, unplugged the electrical connections, reversed these steps in installing the new element. "A Piece Of Cake!"

unplug the oven and pull it away from the wall. looking at the oven from the back, the spark module is at the bottom on the lower left. there is a two piece sheetmetal cover over the area of the spark module. use a phillips head screwdriver to remove five screws and the covers come off. the spark module is the blue cube with four push on wire connectors. all you have to do is hold the new one next to the old one and swap one wire at a time. both were clearly marked with identical numbers and letters. really nothing to it. it took me longer to clean the back of the oven than to replace the module. the old module was eaton part number Y-54052-3. the new one is eaton part number Y-054052-34.

Purchased 2 piece broiler pan from this site

My husband threw a pot holder on the hot (not lit) burner grate.The potholder melted on the grate and we were not able to remove the melted fabric. We ordered a new grate and it looked so good we ordered three more. I am planning to replace the burners next. We'll have a brand new looking cooktop. The cooktop is 15 years old.

Serviceman took out broken glass by removing door and separating front of door from back of door. He carefully removed all broken glass Then replaced with new glass and fastened door together . He did repair in 20 minutes. Oven is like new. Thank you very much for still stocking this part that allows me to keep my oven repaired.

I had an appliance repair rep do the replacement. He made it look relatively easy.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exposing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.

Opened the oven door and locked the spring hinges in the opened position with two 10p nails. Removed the oven door. I dismantled the component parts of the door. I then removed and replaced the broken glass unit,reassembled the door, slid the door onto the hinges, tightened two screws to lock the door in place, removed the 10p nails, closed the door----- and that was it. Less than one hour. The job was accomplished using only a Phillips screwdriver.

Using exploded view and previous customers' comments, I disassembled the door. It was primarily a matter of finding all the screws. I recommend taking the door off first (I didn't), but watch your fingers. The hinges have very, very strong springs and you can hurt your or your helper's fingers if you're not prepared. The hardest part was keeping all the insulation in place while your're installing the assembly. I also replaced the gasket. That takes four hands, two to hold the gasket in place and two to reinstall the window assembly. To put the door back on the hinges, I pulled them out from the door at a 45-degree angle (takes some effort), put screwdrivers through holes in the hinges, and guided (with help) the door back on.

I removed about 8 screws to disassemble the door to get the gasket in. This was an easy task. On the first use of the oven, it shattered one pane of the double glass door window. I think I installed it backwards since one pane is tempered glass, I believe. I installed the new window and am heating it up now - hope it doesn't break.

None of the surface burners (two Uni-burners) would light without using a match. I first ordered two replacement PS2089818 top burner spark electrodes. I replace one which was very easy - the electrode just clips into the burner - and I traced the wires down to the back bottom of the stove where I found they plugged into an ignition module. The new electrode didn't help, but since all four burners were out it made sense that the ignition module would be the problem and not the two separate electrodes. So I ordered a new ignition module. It plugged in easily with the terminals well marked like the original. I put the original electrode back in and all four burners now light properly with the desired "tic tic tic" sound with the knobs in the "high/light" position.

First I removed the four torx screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I installed the new element in reverse order. Recycled the cardboard box and the old element.