79074403990 Kenmore Range - Instructions

Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.

I pulled my unit out of the wall and noticed that the insulation around the top broiler element was a bit brown. Closer inspection revealed that the element had shorted somehow to the oven itself and caused the element to become non-functional. I tried measuring the resistance first, and it was within typical values for the other elements, but I decided to replace the element anyway.

I ordered from PD and the part arrived just a few days letter by regular shipping. I undid the screws holding in the element, undid the wire connectors and replaced the broken element with the new one. The element worked like a charm and I was back in business for cooking.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Easier than painting my toenails!! The gasket came out easily just by pulling with my hands. Replacing it with the new one was even simpler. The clips are already attached to the gasket and easily slip into the holes on the door. I used the end of a tupperware orange peeler to push the unfinished ends of the gasket into a slot at the bottom and that was it! A new, perfect seal and it looks and works great!

Removed electrical connector and two screws. Attached the electrical connector to the new probe and attached with the two screws.

Removed two screws holding broiler element. Released two spring hangers on near the front of the element. Pulled element away from oven and pulled two wire connectors off. Simply reverse process to install new one. Wasn't the problem.

Pull old switches out with pliers and replugged new switches. On main oven, plug casing was melted (wife left broiler on with oven door closed) so had to break apart old casing and individually plug the the wires into new switch and amazingly, it worked! Just gotta keep the door open when broiling.............

Removed all of the grates, control knobs and gas diffusers. Unscrew the drip pans, two on each pan, which attach the pans to the gas supply. Raised the drip pans from the top and unplugged the ignitors from all pans. Remove the top and the rubber deflector over the ignitor switch. The ignitor switch snaps off and on. One of the seals under the drip pan was broken and needed replaced. I would recommend ordering these also. Turned out this was a good time to give everything a goo cleaning then replace as removed.

I removed the sensor from inside the oven with a 1/4” nut driver, pulled the sensor out slowly and then took the connection apart and found out that the connector was different, I cut the connector off of the oven side and then cut the connector off of the new sensor and wired it together. I am still trying to find the ceramic nuts. My oven is working for now. Very easy fix, just wish there were ceramic wire nuts with the new sensor

Twisted replacement bulb into place easily. Let there be light!

1. Turn off power to the electric oven
2. Removed the two screws in the top side of the oven that hold it into the cabinet.
3. Made a support to set the oven on once you remove it from the wall. Or set it on the floor. You will need help this is not a one person job.
4. Used a Philips head screw drive removed the back of the oven panel. I did not have to remove the whole thing just took out half the screws and the electrical plug for the temperature sensor is right on the edge.
5. Unplugged sensor
6. Took out the two screw on the inside of the oven that holds the thermal sensor in place. Pulled it out the front.
7. Side the new thermal sensor in place replace the screws.
8. Pull the plug out and plug it back in. Check and push the insulation back in place where the thermal sensor.
9. Replace the back and replace the screws.
10. Slide oven back into the wall.
11. Replace the two screws that hold the oven in place in the frame.
12. Turn power back on
Check the temperature

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power