9113632090 Kenmore Range - Instructions

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

I've been searching for new drip pans for my very old Kenmore gas stove for over 5 years, and this is the first company to give me the specialized help to find them. Kenmore drip pans for my model are made by another company, which I did not know, and the customer support rep also was helpful in telling me how to measure the stove opening to get the right size. The price was very reasonable, the installation took 30 seconds, and I am again happy to look at and use my stove. I will make future part purchases at PartSelect. Thank you. J Ahrens

Replaced the 4 plates for the stove. It was easy to order over the website. It was delivered on time. Great service.Totally refer the company to a friend. Great company!

Thanks!

Cecilia Pedersen

replaced lights in refrigirator and freezer

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Removed door from Oven.
removed screws from several components comprising the door and separated pieces.
Removed broken glass.
Prior to putting back together I took advantage of the convenience and used oven cleaner to clean inner portion of door. Installed new glass.
Reassembled door.

Easy

I removed the face of the range back. I did not need to remove the three screws in the back like I thought - just the two torx in the front panel. 2) I lifted the clock face assembly out and up. 3) Look at the very simple wiring. Mine had white and red wire coming out of the "power block". 4) I looked at the old circuit board to see which is line and which was neutral. There was no designation. 5) i removed existing wires. 6) I unscrewed the old clock from its moorings, and saved screws. 7) I made sure the up/down orientation of the new clock was the same as the old one. There is an "up" word on the new circuit board, but with the clock upside down, make sure the buttons are correct. BTW, I had to affix the new clockl/timer cover plate onto the replacement clock, using that "up" word on the new circuit board to orient it. 8) I attached the Red wire to the Line connector on the new circuit board, and the White wire to the prong labelled neutral. 9) I used the old screws to secure the new clock to the range back. 19) There was an extension wire included with the new clock. I did not need to use it. 11) I wrestled the clock/timer back into the range itself, using the two torx I removed to secure it. 11) The new buttons on the left (Timer and Clock) are reversed, so now the Timer is the top butting and the bottom now sets the clock. 12) I do not like the feel and action of the new buttons. They are very stiff, and not particularly easy to push.

Replaced clock/timer from Part Select. Direct replacement and new unit works great.

Started off with a philips screw driver,and a cold beer.Removed the cover for the clock/timer. Removed the clock with a plain screw driver.Reversed the order of removal including another cold beer.Just think,I could become a repairman,with enough cold beer.