Models
>
1036427611
1036427611 Kenmore Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$11.92
This genuine OEM part is a 6-inch chrome drip bowl. The drip bowl fits under the coiled burner elements on your electric range and is used to collect drips and spills that happen while cooking. If the...
In Stock
$22.07
Drip bowls are designed to catch any spills or messes from cooking on your stove top. The bowls sit underneath the burner elements on your stove and can easily be removed for cleaning. If your drip bo...
In Stock
This metallic clip is used to help support the broil element. Sold individually.
In Stock
$51.36
The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.
In Stock
This kit comes with the terminal block, mounting clip and wires.
In Stock
On Order
In Stock
This part attaches to the drawer support to help guide the bottom drawer.
No Longer Available
In Stock
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 1036427611
Viewing 2 of 2Element will not heat
Fixed by these parts
How to fix it
Little to no heat when broiling
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Shaohui from East Lansing, MI
- Parts Used:
- WB17X210
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Bellevue, NE
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Large burner would operate on high setting only.
1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Mont Belvieu, TX
- Parts Used:
- WB17X210
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Surface burner coil did not work.
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet
... Read more
, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Read less
Was this instruction helpful to you?
Thank you for voting!