91192481991 Kenmore Range - Instructions

Very easy repair, Pulled burner coil out, removed old burner bowl. Put in new burner bowl, plugged burner coil back in... easy as 1,2,3

Removed burner element and put in bowl

Ordered the part on Friday, got it on Saturday, very impressive. Be sure to unplug the range or disconnect the power at the breaker box before any repairs are started.

The lower (Bake) element is held in by 2 screws. Remove them and gently pull out the element to remove the power wires connected to the element. These wires are very short and there is not much room in which to work. After having removed the wire connectors one slipped from my fingers and went back in the small opening in the back of the oven where the element is inserted. It took some time to fish out the wire. Not wanting to slide out the range I used some surgical forcepts I happen to have grab the wire ( handy to clip wires or compontents in place for some delicate repairs). Its all blind and the opening is very small plus the insulation must be pushed back to gain access. Anyway I managed to grab the wire, attached both wires to the element, replaced the plate and screws holding the element in place, all finished. Worked great. Other ranges I have owned provided a socket to plug in the element, I guess the bottom line gets in the way of quality.. Being 60 years old the worst part of this job is the getting down on my knees to do the work and getting back up again.

Watched a repairman do it the last time for $200.00. This time I unplugged the stove, unscrewed four screw nuts holding the upper rear cover, unplugged old wires, reconnected new ones, fed them thru to the front, attached them to the new block, screwed the block into place, replaced back cover, stuck the element into place, made my little brother plug it back in and turn it on first. It worked. Cost me $20.00 to do what the repairman did the last time. I also replaced the reflector pans. No-brainer.

Pulled out burner and put new bowls in. Looks like a new stove!

Took 5 minutes to replace the 4 bowls. Ordered the bowls one day & they arrived the next day All went perfect.

Cut the Power! pull out stove remove the 4 screws in the back, disconnect the two wires from the element.Open oven door, remove racks and remove 2 screws holding the element in place. Replace element and the 2 retaining screws, replace racks.On the back of the oven connect the two wires and replace cover. Slide back in place and turn on the power. Done =)

repair took about 30minutes total tiem..first turn off power to stove..then open oven removed racks..used nut drive to loosen top two screw hold element..then remove screw hold temp sensor element...then removed two screws holding broiler element...then removed the top screw ...then pulled element out about 7 inches to expose wire connection..held on with spade lugs.. pulled wires off...element now free to remove ...placed spade lug on new element...put element in pace with top two screws..loosely...then did rear screw that held temp element and broiler element...then tighten all screws ..turned on power..did 15 sec test to make sure wired properly..then 5 minutes to operating temperature... job done...hardest part was crazwling in and out the stove...old bones..

First, we turned off the electricity for the whole house, since we didn't want to pull the unit away from the wall and possibly damage our new floors. We then used a socket wrench to remove the 2 nuts holding in the broken element. After that, we pulled out the old element, and this is where the difficulty came into play. The wires for the element stayed inside the back of the oven, and nothing we did could make them come out. We tried for a long time to get the wires to come back out into the oven, but our fingers were not long enough, and nothing we inserted into the space helped the situation.

Since we had turned the electricity off and still were reluctant to move the oven ourselves, we actually decided to call in a repair person (cost: $90). What he did, though was really simple:

He pulled the oven out from the wall. Used a screwdriver to open the back panel of the oven and was able to pull out the wires. Then, he inserted the new element, hooked it up to the wires, and closed back up the back panel. Then, he moved the oven back into place.

The repair person did this in all of 5 minutes, so if my husband and I had thought about the back panel, we would have easily done it ourselves.

My husband had turned the oven on to cook something and didn't know that I have a plastic tray in there. Well, needless to say I needed to get some new oven racks. I tried to get them through the manufacturer (GE). They were 68$ each. I thought that was a bit steep, so I looked online. I decided to order through PartsSelect. Well...they can 2 days later (the week before Christmas!!)and were a PERFECT fit.
Between the price, shipping speed and quality I will
definitely buy from again and recommend this site to everyone I know!!!!

Oh yeah, I work for Sears too. we have access to all sorts of parts....this site is the BEST for prices and delivery speed!!!!

unplugged unit pulled it away from wall took off the backplates traced wire to plug replaced with part ordered very smooth operation. the most impressive thing to me was i ordered part on computer and it was at my door in 30 hours awesome.

Per the instructions included with part.

I started by lifting the front of the stove and slipping a towel under it so it would slide easier and not scratch the floor. The next step was to unplug the stove, after that, I removed the shelves. The next step was to remove the cover plate on the b ack to expose the connection. I removed the old element by pulling the to slide-on connections and the two mounting screws. At this point I took the time to clean the oven since the element was not in the way. To install the new element I did the opposite of th removal process.

First, I made sure the power was turned off at the breaker box so I didn't electrocute myself. Then, I took out the 2 screws that hold the element in place, then pulled it out and unplugged the wires.
I plugged the wires onto the new element, and replaced the screws. My daughter could have done this....

Took old racks out, slid new ones in....exact match at a huge savings from what GE wanted per rack.
Found the company through a Google search, have it bookmarked and will be back if I need something from them.