Models
>
79075239312
79075239312 Kenmore Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$55.18
If your oven has little to no heat, is not heating evenly, or is reaching too high a temperature, there may be a problem with your oven probe. This probe, also known as an oven temperature sensor or a...
In Stock
Order now and your part arrives by May 2
In Stock
Order now and your part arrives by May 2
$37.49
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills. The surface burner cap is located on the top of the burner head and is used in ranges ...
In Stock
Order now and your part arrives by May 2
In Stock
Order now and your part arrives by May 2
In Stock
Order now and your part arrives by May 2
$25.10
This is a screw for your range or microwave. This part is sold individually. It has a pan head, a pointed tip for use with sheet metal, and an x-shaped drive. This screw is a #8, has 18 threads to the...
In Stock
Order now and your part arrives by May 2
In Stock
Order now and your part arrives by May 2
In Stock
Order now and your part arrives by May 2
In Stock
Order now and your part arrives by May 2
$82.97
This igniter has a short wire harness. The wire length is approximately 6 inches long.
In Stock
Order now and your part arrives by May 2
$167.43
This surface burner grate set is for ranges.
The surface burner grate set provides a stable surface for cookware on the surface burner.
In Stock
Order now and your part arrives by May 2
Common Problems and Symptoms for 79075239312
Viewing 7 of 7Little to no heat when baking
Fixed by these parts
How to fix it
Oven is too hot
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Oven not heating evenly
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Gas smell
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from Spokane Valley, WA
- Parts Used:
- 316116400
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven light receptacle broken - bulb base broke off
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven,
... Read more
and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from ASHAWAY, RI
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven did not heat up
Replaced the probe because that's what this site recommended.The oven still does not heat up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from spring, TX
- Parts Used:
- 316490000
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
oven temp not consistent with setting
took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.
Was this instruction helpful to you?
Thank you for voting!