1199098410 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia from Fulton, MO
- Parts Used:
- WFCB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water in Frig was tasting bad.
I turned the cap for the old filter and pulled it out . Then I put in the new one in and turned the cap to secure it in frig.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Springfield, VA
- Parts Used:
- WFCB
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
water from refigerator dispenser started tasting bad
I removed the top shelf in the fridge. I then unscrewed the cover to the water filter and pulled the filter cartridge down into the cover. Keep the cover upright as there may be some water in it. I carried it to the sink. I took the new cartridge and ran water through it from the sink, then set it in the cover and took it to the fridge. I pushed the cartridge up into the space that I removed the old one from and screwed the cover back on. Then I took an empty pitcher and filled it from the water dispenser in the fridge door. I did this three times to charge the filter and remove charcoal dust. Water tastes great now. I ordered two filters so I would ony have to buy once a year. Great site to order the filters from. Cheaper than other sources and delivery was quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Lowell, NC
- Parts Used:
- WFCB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace water filter
It was really easy. All you have to do is twist the old filter out, stick in the new one and twist!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Spring Valley, AL
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from New Port Richey, FL
- Parts Used:
- 5303935086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
High heat reluctant to turn down.
Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Attica, MI
- Parts Used:
- 5303935086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Right front burner would over-heat
First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.
When the switch arrived I went thru the above replacing the bad switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from hollywood, FL
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
corroded terminals
was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Saint Louis, MO
- Parts Used:
- WFCB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The water coming from the dispensor (and the ice cubes) had an off taste
I didn't know where to go to get the filter, so I went to Parts Select.com, they had the filter in stock. I placed the order and when I received the part (in about 4 days) I was able to get it put in & working in about 15 minutes. The water from the dispensor & the ice cubes taste a lot better. Now that I know where to get parts I won't wait that long to change out the water filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- elizabeth from tioga, TX
- Parts Used:
- WFCB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing water filter
this repair was easy.just screw off the cap and the filter is inside and put new filter in the cap and replace.that is all there was to it and i was glad i could do it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shaun from Whitehall, MD
- Parts Used:
- 5303935058
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Block terminal burnt out, hot plate not working, needed to replace the terminal block
This should take approx 15-30 mins. It took me 1.5 hours as I pushed the terminals into the wrong end of the block. It's very difficult to get them out when you do that... However, there are no easy instructions on the block or in the instructions to tell you which end to push the terminals into!!! So, with a 50:50 chance of getting it right, I got it wrong. I think most people would need to buy a new part if they do this. It would be very much easier if the block, had an arrow that simply said IN here so that this type of simple mistake is less easy to do... If you get that right, the fix is quite and straight forward. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Mulvane, KS
- Parts Used:
- 5303935086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The left front burner would not turn off, and the switch was sparking
First I unplugged the stove, and removed the upper-back panel. Then I pulled off the control knob. Then I removed the two screws holding the switch to the stove. Then one-by-one I removed the wires from the old switch and connected them to the corresponding tabs on the new switch. Then, using the knob adapter supplied with the new switch, I figured out how much of the knob shaft I had to remove from the new switch to position the knob the correct distance from the face of the stove. Then I tested the switch with a voltmeter as instructed, and then I hooked up the last wire.
Partselect.com is an awsome website!!! I was able to review comments form other do-it-yourselfers that had similar problems. Then I looked up the Partselect schematic drawings of my stove and was easily able to find and order the part I needed. The part arrived at my house within a couple of days and I had the stove fixed in no time.
Partselect.com is an awsome website!!! I was able to review comments form other do-it-yourselfers that had similar problems. Then I looked up the Partselect schematic drawings of my stove and was easily able to find and order the part I needed. The part arrived at my house within a couple of days and I had the stove fixed in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Ashton, IA
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
burner wouldnt heat
removed element , cut wires, conected wires,replaced element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dung David from Phoenix, AZ
- Parts Used:
- WFCB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace old water filter
The untwisted the water filter took out the old water filter and replaced it with the new one and twisted the cover back on. it was very easy to do and now the water tastes very fresh :) thank you
Was this instruction helpful to you?
Thank you for voting!
Springs pooped off door hinges, causing hinges to break through door face
Remove decorative side panels on stove to expose backside of hinge and springs;
remove door;
remove old hardware;
since hinge openings were bent, straighten hinge opening in oven face;
attach spring to inside of oven;
slide hinge through opening;
attach spring to hinge;
screw hinges to oven face;
repeat on other side;
attach hinges to door;
while decorative panels are off, vacuum
install decorative panels.
DONE.
remove door;
remove old hardware;
since hinge openings were bent, straighten hinge opening in oven face;
attach spring to inside of oven;
slide hinge through opening;
attach spring to hinge;
screw hinges to oven face;
repeat on other side;
attach hinges to door;
while decorative panels are off, vacuum
install decorative panels.
DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darren from San Diego, CA
- Parts Used:
- 5303935086
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Old switch killed by a short between wires
Turn off the electricity
Remove knob
Unscrew old switch
Lift stovetop & prop
Remove wires from switch
Remove switch
Plug wires onto new switch
Put new switch in place
Shut stovetop
Screw new switch in place
Trim knob post
Put adapter on post
Put knob back on
Turn electricity back on
Cook dinner :)
Remove knob
Unscrew old switch
Lift stovetop & prop
Remove wires from switch
Remove switch
Plug wires onto new switch
Put new switch in place
Shut stovetop
Screw new switch in place
Trim knob post
Put adapter on post
Put knob back on
Turn electricity back on
Cook dinner :)
Was this instruction helpful to you?
Thank you for voting!