W130-C Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from Decatur, GA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
Burned terminal block and filter board
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Wayne, NJ
- Parts Used:
- 7902P097-60, 3804F051-80
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Inner Oven Glass broken
I removed two retainer screws which released the outside panel.
Next I removed 2 screws which hold the middle glass pane from one of its retainer brackets.
The was another panel with 4 screws to remove before reaching the final glass inner assembly.
Once that panel was reoved with the broken glass it was time to put the repacement glass assembly back together.
Next I removed 2 screws which hold the middle glass pane from one of its retainer brackets.
The was another panel with 4 screws to remove before reaching the final glass inner assembly.
Once that panel was reoved with the broken glass it was time to put the repacement glass assembly back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from Hudson, CO
- Parts Used:
- WPY04000041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element burned out
Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Morgantown, WV
- Parts Used:
- 12001106
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven door latch was bent and did not release or lock
Had to disassemble the top of the stove and the control panel on the front. I took digital pictures as I disassembled so I could refer to them when putting the stove back together, especially when disconnecting wiring. It took about 3 hours, but most of that time was spent thoroughly cleaning 16 years of baked on grease from places that are normally unaccessible. The new latch works great - the wife is happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Morganton, NC
- Parts Used:
- WPY04000048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Broiler unit would only heat on one side
Removed the screws that held the element and disconnected it. Placed the new element in the proper place, connected the wiring, and replaced all the screws. The unit worked beautifully, and all is well. My wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from FREDERICK, MD
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Stove top wouldn't come on. Oven couldn't go higher than low heat
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.
Sincerely
Peter from Maryland
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.
Sincerely
Peter from Maryland
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from aiken, SC
- Parts Used:
- 7201P015-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replace light in oven
remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachael from Adams, MA
- Parts Used:
- 7711P172-60
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Timer know would no longer set the time...
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the switch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from San Rafael, CA
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replacement of broil element in wall oven
In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw driver is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jared from UNION GROVE, AL
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Houston, TX
- Parts Used:
- W10125458
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Uneven Heating/ High Heat Broiler To No Heat
After replacing heating element then selector switch, I came to think the only other thing was the thermostat. It finally worked. . . But not without some tribulations. This note is for a repair involving thermostat for a w130 jenn-air or maytag wall oven, do not follow instructions included with replacement part! It says the br and ba terminals are to be reversed with this replacement part. . . Not so! After re-connecting (as per instructions) nothing worked! If you have this model jennair or maytag, my suggestion is to replace the wires to connections just as they were removed from the old one. I finally did this after much frustration and electrical testing with a multimeter. Hope this note helps someone. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Prescott, MI
- Parts Used:
- 7201P036-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Burned up oven door gasket needed replaced.
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!