10RJ36-G Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from Los Alamos, NM
- Parts Used:
- WB44X5043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The oven's bottom bake element burned up
First I turned the circuit breaker switch off for the stove unit. I then removed the two screws that hold the element in place at the back of the oven. I then pulled the element out about 3 inches and disconnected the two wires. I attached the new element, bolting the wires into place and then screwed the element back into place on the back wall of the oven. I flipped the breaker switch back on, and turned on the oven. I was done in roughly 15 minutes. The most difficult part was having to shine a flash light into the oven to replace the part, and negotiating the hard cold kitchen floor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Kiowa, CO
- Parts Used:
- WB44X5043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The oven element burned completely into.
I first removed the two screws holding the element in place. Then I pulled the element out about 2 or 3 inches and then took out the 2 small screws holding the 2 wires in place. I then removed the old element and discarded it and installed the new one in the reverse order that I took out the old one. It was quite easy to do, only took about 10 to 15 minutes total time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from SAN DIEGO, CA
- Parts Used:
- WB2X5103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old gasket (seal) broken and leaking
The oven is 70 years old and used several times a week so getting it to come apart wasn't working.
Used a light oil and some thinner to work loose the old seal, which was stuck pretty good, removed it by lightly prying the seal lip wider and pulling it out, mostly piece by piece. The worked in the new one and became of the light oil, it went in rather easy. Had to trim an inch or so from each end and wiped down and cleaned up. No more problems....
Used a light oil and some thinner to work loose the old seal, which was stuck pretty good, removed it by lightly prying the seal lip wider and pulling it out, mostly piece by piece. The worked in the new one and became of the light oil, it went in rather easy. Had to trim an inch or so from each end and wiped down and cleaned up. No more problems....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Phoenix, AZ
- Parts Used:
- WB44X5043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Bishop, CA
- Parts Used:
- WB2X5103
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
worn out gasket
Used a putty knife and dental pick to remove old gasket remnants and installed new gasket with putty knife and thumb pressure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erbin from Poquoson, VA
- Parts Used:
- WB44X5043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element burned into.
TURN POWER TO OVEN OFF AT POWER PANEL 1- Remove element: 2 screws ... cut wire at element because of burned area. 2- Crimp two new wire lug connectors onto wire and attach to new element with supplied screws. 3- Attach element to back of oven: 2 screws ... TURN POWER ON AGAIN AND TEST OVEN
Was this instruction helpful to you?
Thank you for voting!