RC547*01 Hotpoint Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, reconnected the wires to the new element, reattached it to the oven and voila!

It worked. What was really cool, once I ordered the part, I received it in only two work days!

Good job folks!

Hardest part was getting the wrong element and having to send it back and reordering correct one....too many variables. Two screws inside the oven removed, pull out range and take off back and attach new element to plug ins!

Turned off power at breaker panel. Removed 2 screws attaching element to stove. Pulled element out a couple of inches and removed 2 wires attached with screws. Installation is reverse order of removal.
Be careful not to twist the terminal ends when tightening screws.

shipping was very fast!

Of course I unplugged the stove. Then I removed the cover to reveal the connections for the element. After unscrewing the two wire connectors, I had to use a nut driver to remove the two screws holding it in place in the oven. The new element went in easily. I screwed it in place in the oven and then attached the two wires in the back and replaced cover. Plugged it in, tested it, and we were good to go.

Note: this was a second attempt, The first time I ordered a heating element with push on connectors not screw on. Beware! Pay attention to the pictures and description. I ordered too quickly.

Our element blew in our oven, we took it out and saw what we needed. It was very easy to see what part we needed to order because of the great pictures on the website. The larger views really helped. We got the part quickly and put it in. It was a breeze and now our oven is working great! The best part however, is it only cost about $33.00 including shipping and handling. Much cheaper than if we would have had someone come in to fix it!

First, shut off the breaker to the stove. Removed old element by unscrewing the two screws on the plate where the element attached at the bottom of the inside of the oven. The old element was corroded at the connection, so disconnect it, attached the new one, pushed it back in the insulated socket then reattached the two screws on the plate. Flipped the breaker back on. Works great. Only took about 25 min. from start to finish.

this repair is simple. Just unscrew the existing connection and attach the new heating element. You may have to break the existing ceramic element, but a new one comes with the new heat element.

I removed the screw holding the tilt-lock hinge, then removed the insulator brackets and unscrewed the wire terminals. Units come with new insulators, brackets, terminal screws & hinge screw. This is a very straightforward operation.

Note: Please make sure power is off!!! Turn off at the fuse panel,Main. Test oven after you turn off breaker...try turning on oven with normal switch, indicator light should be off. Also check interior light, usually wired 110 volts, may be on a separate circuit, just for safety!!. Remove retaing screws, scewdriver will work , but a nut driver is easier. Pull old element out gently and check between terminals with volt meter. Remove screws on element holding feed wire, reverse this process to install. Test oven for proper operation after installation...make sure oven cycles through a set temperature range.

I removed the screw holding the tilt mechanism to the range top. Removed the clips holding the block together. Disconnected the two power leads on the old burner and replaced with the new burner. Closed the block around the leads. Screwed the tilt mechanism back to the range top and that was it!

Finding the replacement part on partselect.com was easy. The search feature brought me to a diagram of the bake element and offered precise grid measurements to assure me it was the correct part.

Be sure to completely unplug your stove before doing anything. The only tools I used were a small nut driver, a standard pliers and a flashlight (and a cushion for my old knees, ha).

Installation was easy, but you have to be very careful to not bend the little prongs were you attach the element to the stove wires... they bend pretty easily, so hold them tight or hold them in a pliers firmly but without crushing them. Drive the two screws to attach the element to the wires; then, drive the two screws to hold the element face plate against the rear of the oven, and viola, you're done!

Thanks, partselect - website, price, packaging and shipping were perfect! Also, I got several good tips from the feedback of other customers that were very helpful. That is a nice feature of your website and a good customer service.

Before you start, make sure the circuit breaker is not tripped, which can explain element not heating.
In my case, the toaster element was ok, which tells us that the oven is receiveing electric current.
1) Take the grills out so you have free access
2) Remove the door - this model just pull it up to let it free
3) remove the 2 screws securing the element on backwall of the oven and gently pull the element out
4) if you have a multimeter:
a) set it to AC, greater than 300 V
b) use your alligator clips, attach the clips
to the contacts of the element
c) briefly turn the oven on: expect to read between 230 and 260 volts
5) remove the screws securing the old element
6) install the new element;
7) secure the element back to the backwall
8) turn the oven briefly on and feel the heating element: should come warm pretty quic;
- Job done -

When you remove the screws securing the wire to the old element, make sure the wires are not cracked, or interrupted.

Otherwise, a real simple and easy fix.

Specs of this element are what I missed but here they are:
Resitence : 25.5 Ohms
Volts: 230 - 260Volst
Power : 2050 to 2650 Watts
The power depends on the voltage, so make sure you dont have it too low (less than 220 ) or too much (yeah, 260V is nearing upper limits)

Removed two clips that held the ceramic insulators in place. Removed two screws that held conductors to the burner. Replaced screws onto new burner unit, replaced ceramic insulators. Fastened clip to burner onto the range. Turned burner on and it worked great. Thank you for your quick responce to my order.

Removed trim ring and drip pan, loosened retaining nut and replaced the burner. I was very impressed at the fast service from your company. Thank You

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the wires to the new element. pushed the element back in place the screwed it back to the back of the stove.