QSS740RN1SS Haier Range - Instructions

I started by Unscrewing the range top. 2 small screws. I took off the old piece by unclipping the piece . Then I color coded each wire so that I would know exactly where I would place the wires for the new part. 30 min maximum time spent changing the part. Please don't forget to unplug the range before you start.

Per the instructions included with part.

removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.

Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel

I downloaded the installaion manual from the web for this model. First htings first, I located the circuit breaker for the oven and turned it off. Removed the lower trim piece from the bottom, next lifted the oven door off its hinges and set it to the side. I then wrapped a couple of small towels around the hinges for the door as per the manual (the hinges can pinch a finger). I then removed the four screws which secured the oven into the cabinet. Next I slid the oven forward allowing me access to the rear. I removed the pieces from the rear to gain access to the sensors connector, and unpl;ugged the sensor. Went around to the front and unscrewed the 2 screws securing the sensor and removed it. I then installed the new sensor, replaced the rear covers, slid the oven back into the cabinet, secured the four screws, snapped on the lower trim, remounted the oven door, and turned the breaker on. Oven working fine now.

Took off oven door and removed racks. Removed the cover on the back side (5 screws removed with nut driver) Pulled sensor out the front side of the oven. Threaded the new sensor through and put all back together.

Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

Turn off breaker to stove. Remove 2 screws in front under stove top molding. Raise stove top from front on hinges in back. I used a piece of wood to support top up while I worked on burner. Remove screws holding old burner in place. I found my problem on the old burner - the outer element had been shorted and fried. Carefully remove each wire and reinstall in new burner in proper location. Reinstall burner and stove top with old screws.

I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

1st replacement part was damaged from Shipping.
Parts Select sent a new one that i received in only a few days.
our stove is slid into a granite island so the disassembly was not as simple as most. It was necessary to remove the controls, the controls housing & screws along the top of the oven door.
Within an hour the stove was back in place and working perfectly.
Great service from Parts Select

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

It’s easy to replace and you can found out the video from YouTube to follow the instructions

Pull the range out from the wall to access the rear of the unit. Turn off power to the range by unplugging from the wall or turning off the breaker.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unplug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.