GAK26HA Glenwood Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Diana from Jacksonville, FL
- Parts Used:
- 31829401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
electric ignite gas stove kept clicking the ignitor unless unplugged from electrical outlet
I removed the 2 screws that held the housing on at the back of the stove. Then I removed the 2 screws that held the module to the back of the stove. Since I am not an experienced electrical person (I am a female nurse in the operating room), I unplugged 1 wire at a time from the old module and plugged it into the new module. I repeated this step with each wire to make sure I didn't put the wrong wire on a wrong spot until I had all the wires to the new module. Then reattached the screws, plugged in the oven and presto, it works just fine! Was amazed at how easy it was. A 50 dollar part instead of a new 1500 dollar stove. How easy is that?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lansing, MI
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Perth Amboy, NJ
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left rear burner would not ignite
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Las Cruces, NM
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
two burner ignitors would not function on cook stove
1. ordered two new switches
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lake George, CO
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right front gas burner ignitor wouldn't spark
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVEN from MARSHFIELD, MA
- Parts Used:
- Y07514500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace the 4 chrome bowl liners on our Glenwood Gas stove
It was straight forward to find the part which could be identified by picture and detailed dimensional description. Very easy to throw out the old rotten liners and replace them with the parts sent.
Was this instruction helpful to you?
Thank you for voting!