CRCL3630SM-1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Perry from Flushing, NY
- Parts Used:
- F26T8-CW-4
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
remove and replace
very easy remove the bad bulb install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Apple Valley, MN
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
bottom trim had rusted, so we needed new piece
Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked open!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from Port Richey, FL
- Parts Used:
- WB07K10250, WB07X10170
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
replaced more for cosmetic reasons
Your support team helped tremendously in ordering the parts. Parts arrived in only 2 days. Upon taking the door off the oven we had to remove several screws, then more screws. Was able to take it almost fully apart, replace old broken parts with new. Putting it back together was like a puzzle. We did it though and saved money! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from FAYETTEVILLE, NY
- Parts Used:
- WB07K10250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.
Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LORDSBURG, NM
- Parts Used:
- WB1X500D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
No Spin Cycle
Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeannene from HUNTINGTON, TX
- Parts Used:
- WB07K10250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Part rusted over time...22 years.
Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Sarasota, FL
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
rusted trim strip
remove screws, re-install screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from West Melbourne, FL
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The trim piece on the bottom of the door was rusted making the unit look really dirty and used.
It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from buford, GA
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
bottom trim had rusted out from water build-up
disassembled bottom trim on oven door.cleaned area of excess rust and installed trim piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Dills burg, PA
- Parts Used:
- WB1X500D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Heating element quit working after 30 years
Removed several screws and removed element. Replaced same. Total ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danial from HILLSBORO, TX
- Parts Used:
- F26T8-CW-4
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fluorescent lamp bulb
Unscrew the metal rim and remove the glass window. Remove the old bulb by twesting the bulb towards you. Place the new bulb's pins into the slots and twest away from you. Place the metal rims back in place and screw them down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from NORTH HAVEN, CT
- Parts Used:
- WB7X7187
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
End cap broke on handle
Opened oven door removed screw and broken end cap. Replaced with new end cap and put handle back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from san jose, CA
- Parts Used:
- WB36X192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vanessa from runnemede, NJ
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
the paint started to chip off.
remove the door, removed about six screws and did a clean up on the glass. the replacement part was screwed back in place. so easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Eden prairie, MN
- Parts Used:
- WB44T10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Convex element burned out
REmoved the covers, removed the old part, be careful with the electrical connections, they move back behind the wall and are hard to get back in the open. While waiting for the new part, 2 days, I cleaned the oven. Works like new.
Was this instruction helpful to you?
Thank you for voting!