PCGB995SET1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from Okmulgee, OK
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Lamp Holder Burned
removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from Kenner, LA
- Parts Used:
- WB13K10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not lite
openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from SAYREVILLE, NJ
- Parts Used:
- WB13K10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Bottom oven wouldn't warm up
Remove the door for easier access. Remove the fan cover from the back of the oven (about 6 Phillips head screws). Remove the bottom cover (2 5/16" screws). Lift the cover from the back and slide out. Remove the old igniter (2 5/16" screws). Pull the oven away from the wall. Remove back cover (3 5/16" screws). Unplug igniter, feed wiring through the oven. Install new igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mchael J. from Chesterfield, VA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven post mini explosion sounding
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from South Haven, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Kaplan, LA
- Parts Used:
- WB13K10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Change bad/broken igniter on gas stove top burners
Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Rio Vista, CA
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven light did not work
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitzi from Briarcliff Manor, NY
- Parts Used:
- WB28K10222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janine from Wind Gap, PA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mel from LOGAN, UT
- Parts Used:
- WB20K10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
temperture
replace sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ARDMORE, PA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hole burned through deflector oven and metal dropped onto igniter and burned it out
Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CUMMING, GA
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.
First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gansevoort, NY
- Parts Used:
- WB08T10002
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
wire connection to socket was bad
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryl K. Pesce from MILLSBORO, DE
- Parts Used:
- WB13K10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lower oven igniter tip burned open.
This is the 2nd igniter I purchased from your company. The first igniter I purchased from your company only lasted for 4 months. The parts your company sell have GE genuine parts on the packing box. Why would a new igniter only last for 4 months?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from DEARBORN, MI
- Parts Used:
- WB13X26360
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
One burner would not light from spark. All other burners lite with spark.
First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Was this instruction helpful to you?
Thank you for voting!