JCGB860SEJ3SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from Okmulgee, OK
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Lamp Holder Burned
removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from TWIN FALLS, ID
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Interior light needed replaced
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from BELLEVUE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitzi from Briarcliff Manor, NY
- Parts Used:
- WB28K10222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Rio Vista, CA
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven light did not work
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gansevoort, NY
- Parts Used:
- WB08T10002
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
wire connection to socket was bad
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from SAINT PAUL, MN
- Parts Used:
- WB31X24738
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old griddle wore out in less than 2 years
put the new griddle in its place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CUMMING, GA
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.
First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irene H from HENRICO, VA
- Parts Used:
- WB02X24790
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing grate foot / bumper
Put in a new foot / bumper. That's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from N ROYALTON, OH
- Parts Used:
- WB48X20249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed another oven rack. It came with two. Now I have three.
I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Frederick, MD
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Oven Light Assembly damaged
I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BRADENTON, FL
- Parts Used:
- WB21X20262
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burner Valve stopped working
Turned off gas, then lifted up the burner cover and removed the old valve using a screw driver to loosen the clamp. I also had to remove the face plate using a socket set (4 screws). I didn't align the valve using the existing valves as a guide and also didn't get the clamp tight enough. So I re-aligned the valve to match the other valves and also tighten the clamp enough as best I could to prevent gas from leaking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from DEARBORN, MI
- Parts Used:
- WB13X26360
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
One burner would not light from spark. All other burners lite with spark.
First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!