Models > JGB850SEF1SS > Instructions

JGB850SEF1SS General Electric Range - Instructions

Jump to:

All Instructions for the JGB850SEF1SS
1 - 15 of 55
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jack from Okmulgee, OK
Parts Used:
WB08T10002
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven Lamp Holder Burned
removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.
23 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond from Waukegan, IL
Parts Used:
WB2K101
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
burner grate bumpers/feet missing
Hi temp (900 deg) engine gasket adhesive on numbs and press in. DONE !
13 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Elizabeth from MECHANICSBURG, PA
Parts Used:
WB29K10024, WB29K10023, WB29K10022, WB28K10222
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
This was not really a repair. Just replacement. The burner caps get discolored rather quickly and nothing removed the stains. I'm thrilled to have replacements on hand.
Removed the old caps, replaced them with the new ones.
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bret from South Haven, MI
Parts Used:
WB16T10046
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kim from Santa Rosa, CA
Parts Used:
WB29K10024, WB29K10023, WB29K10022
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Our burner caps had started chipping.
Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!
12 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
brigitte from vacaville, CA
Parts Used:
WB31K10217
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The griddle needed to be replaced
Lifted the old one off and placed the new one on. Fits perfectly and looks great!
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mitzi from Briarcliff Manor, NY
Parts Used:
WB28K10222
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Howard from Rio Vista, CA
Parts Used:
WB08T10002
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Oven light did not work
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
9 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Gansevoort, NY
Parts Used:
WB08T10002
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
wire connection to socket was bad
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janine from Wind Gap, PA
Parts Used:
WB16K10055
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert K from York, PA
Parts Used:
WB16K10070
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Needed To Replace Burner
Took longer to open the box.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
mel from LOGAN, UT
Parts Used:
WB20K10027
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
temperture
replace sensor
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from CUMMING, GA
Parts Used:
WB08T10002
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.
First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from PLAINFIELD, NJ
Parts Used:
WB2K101
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Misleading ordering information: a HUSTLE
I specifically asked if $16 plus would be the sole expense for this item. I was told that it would be plus there would be no cost for return of the rubber feet. Several hours later I was emailed an invoice that the cost would be $26 plus for four rubber grill screw-like items, a vastly over-priced item. I called and learned through the email system that the item had not been shipped. I requested cancellation at 5AM Saturday. Friday night order led to Saturday morning cancellation -- and Monday morning delivery despite my specific request to cancel. I am not satisfied. It seems like I have been hustled.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Astrid from MORAGA, CA
Parts Used:
WB16K10055, WB29K10023
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
THE OLD BURNER HEAD WAS NOT TURNING ON PROPERLY AND THE GAS CAME OUT UNEVEN.
I JUST EXCHANGED THE BURNER AND BURNER CAP.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGB850SEF1SS
1 - 15 of 55