JGB900CEK5CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glen from Kenner, LA
- Parts Used:
- WB13K10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not lite
openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marjorie from Yucca Valley, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pies Boiled Over And Baked On Oven Bottom
Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Albuquerque, NM
- Parts Used:
- WB24T10147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Convection oven fan and door light not working
The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)
Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two hex head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.
Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.
Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two hex head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.
Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Goshen, IN
- Parts Used:
- WB16K10035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench set
Oven burner was burned out, wouldn't light
Pull plug and shut off gas! The lower oven burner is held in with two rear and one front screws. I removed the top floor of the oven (two hand tightened screws at the back), the bottom drawer, and the front door (just lift it off the hinges). This allowed me to access the burner, and I removed it by unscrewing the three screws, unhitching the igniter connector, and lifting the burner and igniter up and out. I connected the new igniter on the new burner before installing it in the oven, and found that the connector did not match (I was warned about this possibility on the PartSelect site), but instead of splicing the wires together, I cut off the connector on the new igniter and replaced it with the connector of the old igniter. Then I screwed the burner into the oven, recoupled the connector, replaced the floor, drawer, and door, and I was done! It took about 45 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Houston, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven rack missing when I purchased the house
I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from TWIN FALLS, ID
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Interior light needed replaced
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- noreen from flushing, NY
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed extra oven space
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from South Haven, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from 29 Palms, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom tray would not clean up.Looked like finish was off it
removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from BELLEVUE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Kaplan, LA
- Parts Used:
- WB13K10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Change bad/broken igniter on gas stove top burners
Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from TUCSON, AZ
- Parts Used:
- WB08T10026, 40A15
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Replace Oven light socket and light bulb in kitchen Range
1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from malden, MA
- Parts Used:
- WB13X42446
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
one burner would not light
opened back panel. noted location of colored wires. disconnected wires & removed module. attache wires to new module & attached module to panel. closed up back panel. tested all burners
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janine from Wind Gap, PA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert K from York, PA
- Parts Used:
- WB16K10070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed To Replace Burner
Took longer to open the box.
Was this instruction helpful to you?
Thank you for voting!