Models > JSP39GR1

JSP39GR1 General Electric Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for JSP39GR1

Viewing 5 of 5
ELECTRIC RANGE Diagram and Parts List for General Electric Range
ELECTRIC RANGE
ELECTRIC RANGE Diagram and Parts List for General Electric Range
ELECTRIC RANGE
RANGE Diagram and Parts List for General Electric Range
RANGE
RANGE Diagram and Parts List for General Electric Range
RANGE
RANGE Diagram and Parts List for General Electric Range
RANGE

Manuals & Guides for JSP39GR1

Click to download
Manual
Owner's Manuals
(3.07MB)
Keep searches simple, eg. "belt" or "pump".
Switch – Part Number: WB24T10147
$27.83
This light switch is controlled by opening and closing the oven door
In Stock
Order now and your part arrives by May 14
Door Lock and Switch Assembly – Part Number: WB49T10020
$151.12
In Stock
Order now and your part arrives by May 14
Inner Door Glass – Part Number: WB56X1907
No Longer Available
Limit Switch – Part Number: WB24K5085
$57.30
In Stock
Order now and your part arrives by May 14
OV Door GLASS Assembly-WHITE – Part Number: WB57K5182
No Longer Available
Manifold End Cap – Part Number: WB36K5135
$31.05
Special Order
DOOR LOCK PLAT – Part Number: WB34K5228
$76.42
Special Order
LEVER LOCK – Part Number: WB15K5016
$52.50
Special Order
INSULATION-BACK & Bottom – Part Number: WB35K5113
$72.17
Special Order
OV Door INSULATION – Part Number: WB35K5026
$58.37
Special Order
GLASS OV Door INNER – Part Number: WB57K5102
No Longer Available
LOWER FRONT PANEL – Part Number: WB56K5017
$84.30
Special Order
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Michael from Albuquerque, NM
Parts Used:
WB24T10147
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Convection oven fan and door light not working
The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two he x head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.
Read less
18 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eugene from Hilton Head, SC
Parts Used:
WB24T10147
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Burnt Smell
Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Read less
8 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More